Results 181 to 190 of about 897,876 (338)

Powder Metallurgy Preparation of Metastable β Ti–Cr–Ge Alloys for Medical Applications

Advanced Engineering Materials, EarlyView.
This study develops metastable β Ti–Cr–Ge alloys using powder metallurgy for biomedical implants. The Ti–10Cr–2Ge alloy exhibits superior mechanical performance with high yield strength (>1100 MPa), low Young's modulus (<85 GPa), and excellent strain hardening behavior.
Teddy Sjafrizal, Damon Kent, Ali Dehghan‐Manshadi, Matthew S. Dargusch   +3 more
wiley   +1 more source

Kinetics of Growth Retardant and Hormone Interactions in Affecting Cucumber Hypocotyl Elongation [PDF]

, 1967
Thomas C. Moore
openalex   +1 more source

Optimized Strategy for Fabricating High‐Aspect‐Ratio Periodic Structures Over Large Areas Using ps‐Direct Laser Interference Patterning

Advanced Engineering Materials, EarlyView.
Picosecond direct laser interference patterning (DLIP) enables precise microstructure fabrication on stainless steel. Using a multiscan approach, high‐aspect‐ratio patterns are achieved. Fluence influences structure growth and homogeneity, with smaller periods yielding better uniformity.
Fabian Ränke, Marcelo Sallese, Marcos Soldera, Ignacio Tabares, Flavio Soldera, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Sol–Gel Synthesis of Ca2.5Ag0.3Sm0.2Co4O9 Semiconducting Materials for Thermoelectric Applications in Aerospace Systems

Advanced Engineering Materials, EarlyView.
Ca2.5Ag0.3Sm0.2Co4O9 semiconductor materials are synthesized and produced in this study using the sol–gel and cold pressing techniques for thermoelectric generator applications. As template samples are added, the Seebeck coefficient and power factor values rise, peaking at 800 °C for Ca2.5Ag0.3Sm0.2Co4O9 at 274.47 μV K−1 and 0.58 mW mK−2, respectively.
Enes Kilinc, Fatih Uysal, Mucahit Abdullah Sari, Huseyin Kurt, Erdal Celik   +4 more
wiley   +1 more source

Titanium‐S23: A New Alloy with Ultra‐High Tensile Toughness Directly from the Solid‐State Processing of Recycled Ti–6Al–4V and Ti–5Al–5Mo–5V–3Cr Powders using Field Assisted Sintering Technology

Advanced Engineering Materials, EarlyView.
This study explores combining two existing aerospace titanium alloy powders, processing them via field‐assisted sintering technology and the subsequent discovery of a novel alloy composition, termed S23, with ultra‐high tensile toughness. Fine‐scale alpha precipitates favorably form in the alloy despite the relatively slow cooling, providing an ...
Samuel Lister, Gavin J. Baxter, Martin Jackson   +2 more
wiley   +1 more source

On a Formula for reducing Observations in Azimuth of Circumpolar Stars near Elongation, to the Azimuth at the greatest Elongation [PDF]

Shortrede
openalex   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

The elongated shadow

Comprehensive Psychiatry, 1970
openaire   +3 more sources

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

Study on elongation master curve of thermal aging composite modified double base propellant. [PDF]

Sci Rep
Zheng J, Liu J, Deng H, Dang J, Yang C, Sun Z, Guo Z, Xu J, Chen X.   +8 more
europepmc   +1 more source