Results 11 to 20 of about 820 (211)
On-load Back-EMF Optimization Based on the Back-EMF MST Method and Parametric Optimization [PDF]
This paper proposes an optimal design for a surface mounted permanent magnet synchronous machine (SM-PMSM) based on parametric optimization process to reduce the on-load Back-EMF distortions caused by an increase in the electromagnetic load and in the ...
Luiz Henrique Reis de Jesus +2 more
doaj +3 more sources
Thermodynamic investigations of the erbium tellurides by EMF method
The work presents the results of a thermodynamic study of the Er-Te system by the method of electromotive forces (EMF) in the temperature range of 300-450 K. From the EMF measurements of the concentration cells relative to the Er and ErTe electrodes, the
S. Z. Imamaliyeva +3 more
doaj +3 more sources
Overview of the Evaluation Methods for the Maximum EMF Exposure in 5G Networks
Instantaneous measurements of the electromagnetic field (EMF) strength do not reflect the maximum exposure levels possible in a given location. An extrapolation factor needs to be applied to the measurements before comparing them against the local exposure guidelines or recommendations for compliance evaluation.
Amina Fellan, Hans D. Schotten
openaire +6 more sources
Thermodynamic investigation of the Bi2Se3–Bi2Te3 system by the EMF method
Binary and complex chalcogenides with a tetradimite-like layered structure are of great practical interest as topological insulators, thermoelectric, and optoelectronic materials.
Gunel S. Hasanova +3 more
doaj +2 more sources
The equilibrium phase space of the Ag–In–Se system in the part AgInSe2–InSe–Se below 500 K consists seven three-phase regions In2Se3–AgIn11Se17–Se (I), AgIn11Se17–AgIn5Se8–Se (II), AgIn5Se8–AgInSe2–Se (IІІ), In2Se3–In6Se7–AgIn11Se17 (ІV), In6Se7 ...
M.V. Moroz +8 more
doaj +1 more source
Equilibrium T–x space of the Ag–Ga–Te system in the GaTe–AgGa5Te8–Te part was divided below 600 K into three-phase regions Ga2Te5–AgGa5Te8–Te, Ga2Te3–AgGa5Te8–Ga2Te5, Ga7Te10–AgGa5Te8–Ga2Te3, Ga3Te4–AgGa5Te8–Ga7Te10, and GaTe–AgGa5Te8–Ga3Te4 by the ...
M. Moroz +5 more
doaj +1 more source
Thermodynamic properties of the GdTe3 compound
The alloys of the Gd-Te system in the range of compositions > 75 at% Te were studied by the methods of X-ray diffraction (XRD) and electromotive forces (EMF). From the EMF measurements of the concentration cells relative to the GdTe electrode in the 300-
Samira Imamaliyeva
doaj +1 more source
The external factors that influence on the thermokinetic EMF value in the Ti – 50 at.% Ni samples were determined. A method for setting thermokinetic EMF in certain sections of the TiNi wire was developed. The thermokinetic EMF value was measured directly
O. A. Petrova-Burkina +2 more
doaj +1 more source
The GeBi2Te4-Bi2Te3-Te system was investigated by XRD and EMF measurements of the reversible concentration cell of the type (-) GeTe (solid) │glycerol +KCl │ Ge-Bi-Тe (solid) (+) in the 300-450K temperature range. It was shown that, in the indicated
T.M. Alakbarova +4 more
doaj +1 more source
Thermodynamic study of a synthetic analog of the famatinite mineral - Cu3SbS4
Fundamental thermodynamic properties of the synthetic analog of the famatinite mineral - Cu3SbS4 were studied on the basis of electromotive force (EMF) measurements.
P.R. Mammadli +3 more
doaj +1 more source

