Results 171 to 180 of about 1,380,005 (303)

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Multi-Objective Optimal Dispatch of Integrated Energy Systems Guided by Dynamic Carbon Emission Factors. [PDF]

ACS Omega
Lin Y, Lu Z, Qin H, Liu Z, Li X, Li G, Wang Q, Wang P, Yang J, Yao S.   +9 more
europepmc   +1 more source

Mixed Use of Bio-Oil in Oil Power Plants: Should It Be Considered When Developing NH₃ Emission Factors? [PDF]

Int J Environ Res Public Health, 2021
Kang S, Woo J, Jeon EC.
europepmc   +1 more source

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

Large differences between UK black carbon emission factors. [PDF]

Carbon Balance Manag
Brighty A, Staffell I, ApSimon H.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Observing the impact of renewable electricity on the emission factors of electric vehicles using electricity generation data. [PDF]

Sci Rep
Zhang X, Su J, Zhou Y.
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Chemical Dissection of PM_2.5 in Cigarette Smoke: Main and Sidestream Emission Factors and Compositions. [PDF]

Toxics
Zhou Y, Huang H, Zou C, Deng M, Tu X, Deng W, Yu C, Li J.   +7 more
europepmc   +1 more source

Calculation of emission factor

, 2010
Производство энергии неизбежно сопровождается загрязнением окружающей среды отходами от производственных процессов и технологий преобразования энергии. В статье я хотела бы охарактеризовать методы, которые могут быть использованы для расчета выбросов парниковых газов для возобновляемых источников энергии.
openaire   +1 more source