Results 101 to 110 of about 6,198 (217)

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Controlling Grain Growth in Powder Bed Fusion of Yttria‐Stabilized Zirconia Using Femtosecond Lasers: Challenges and Methodological Insights

Advanced Engineering Materials, EarlyView.
Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn, Sarah Kaden, Andrea Barz, Daniel Störzner, Jens Bliedtner, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Solvent-Free Synthesis of Ultrabright Carbon Dots With Near-Unity Quantum Yield for High-Performance Light-Emitting Diodes. [PDF]

Adv Sci (Weinh)
Park H, Lee SH, Seo S, Park S, Ji SM, Jo H, Park S, Kim YH, Kwon W.   +8 more
europepmc   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source

Anion-specific fluorescence enhancement <i>via</i> counterion modulation in biphenyl-based porous cage salts. [PDF]

Chem Sci
Sabatino RM, Morey MN, Lovstedt A, Bloch ED.   +3 more
europepmc   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

Advanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe, Louis Becker, Gaurav Kanu, Thomas F. Headen, Dirk Honecker, Gabi Schierning, Santiago Benito, Sebastian Weber, Klara Lünser, Sabrina Disch   +9 more
wiley   +1 more source

Fluorene-Framework Engineering Enables Narrowband Red Multi-Resonance Emitters for High-Efficiency With Negligible Roll-Off Toward BT.2020. [PDF]

Angew Chem Int Ed Engl
Rajput A, S NV, Muruganantham S, Tirupati M, Kumar OP, Kim JY, Chae MY, Kwon JH.   +7 more
europepmc   +1 more source