Results 161 to 170 of about 8,653,074 (198)

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

Advanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe, Louis Becker, Gaurav Kanu, Thomas F. Headen, Dirk Honecker, Gabi Schierning, Santiago Benito, Sebastian Weber, Klara Lünser, Sabrina Disch   +9 more
wiley   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

Advanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source