Results 241 to 250 of about 965,816 (315)

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Mol* web molecular graphics engine. [PDF]

Protein Sci
Rose AS, Tomasello G, Kovács ÁS, Autin L, Sehnal D.   +4 more
europepmc   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Explainable LSTM-AdamW based fault diagnosis of aircraft rotating components using airborne acoustic signals under dynamic operating conditions. [PDF]

Sci Rep
Özüpak Y, Aslan E, Zaitsev I.
europepmc   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Learning-augmented optimization and control of long-haul mobility propulsion systems. [PDF]

iScience
Ding M, Li Y, Chen C, Lei N, Zhang H.
europepmc   +1 more source

Setup‐Optimized Sequencing in Job Shops: Modeling Workstation Productivity and Lateness Behavior

Advanced Engineering Materials, EarlyView.
Setup‐optimized sequencing in job‐shop production creates a trade‐off between productivity improvement and schedule reliability. A WIP‐explicit modeling framework links sequencing‐induced productivity gains and lateness dispersion through the production operating curve.
Friederike Stefanowski, Matthias Schmidt, Peter Nyhuis   +2 more
wiley   +1 more source

CFD-enabled sustainable design and manufacturing of cooling fan for unmanned helicopter. [PDF]

Sci Rep
Si L, Liu Z, Xiao N, Zhang Y, Liu Y, Deng S, Li Y, Yang H, Zhang X, Fu G, Choi JP.   +10 more
europepmc   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Influence of Piston Bowl Geometry and Hydrogen-Diesel Mixing Ratios on Dual-Fuel Engine Combustion. [PDF]

ACS Omega
Kumar R, Nath S, Atul, Ranjan V, Khan S, Ghoshal SK.   +5 more
europepmc   +1 more source