Results 91 to 100 of about 132,128 (305)

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Evaluating the Effect of Turbulence on Aircraft During Landing and Take-Off Phases

International Journal of Aviation, Aeronautics, and Aerospace, 2018
—— Low level wind shear and turbulence present a serious safety risk to aircraft during the approach, landing and take-off phases. Low level wind shear has been identified as one of the primary factors for aircraft go-arounds and aborted landings. During
Anthony O' Connor, Derek Kearney
doaj   +1 more source

3D Printing Innovations in Polymeric Porous and Patterned Architecture

Advanced Functional Materials, EarlyView.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil, Sri Vaishnavi Thummalapalli, Clarissa Westover, Arunachalam Ramanathan, M. Taylor Sobzcak, Roumika Patil, Qixuan Xiang, Tiantian Li, Sui Yang, Timothy E. Long, Hongyue Sun, Xianqiao Wang, Yang Liu, Kenan Song   +13 more
wiley   +1 more source

Rapid near-optimal aerospace plane trajectory generation and guidance

, 1988
Issued as Progress reports [nos. 1-3], and Final report, Project no.
Calise, Anthony J.
core  

Value stream analysis of manufacturing engineering new product introduction processes [PDF]

, 2011
This paper describes the use of a methodology for value stream mapping and analysis of Manufacturing Engineering New Product Introduction processes. The applicability and usefulness of the technique to process improvement in this domain is explored in
Chris Beadle, Shehab, Essam, Essam Shehab, Malachy Maginness, Maginness, Malachy, Beadle, Chris   +5 more
core   +1 more source

In Situ Crystalline‐Amorphous Composite Oxide Structure Suppressing Thermal Wear Instability for Refractory Multi‐Principal Element Alloy

Advanced Functional Materials, EarlyView.
An effective strategy is developed to overcome the medium temperatures wear resistance degradation in refractory multi‐principal element alloys. By utilizing chemical short‐range ordering to trigger oxygen‐induced amorphization, a composite oxide structure is formed, which combines high hardness with robust stiffness.
Xuhui Pei, Jianbao Zhang, Hanming Wang, Yin Du, Tao Yang, Ji‐Jung Kai, Benyebka Bou‐Saïd, Haifeng Wang   +7 more
wiley   +1 more source

Enhancing Quality Assurance using Virtual Design Engineering: Case Study of Space Shuttle Challenger

International Journal of Aviation, Aeronautics, and Aerospace, 2015
Virtual Design Engineering is an emerging method of increasing quality of systems. Including Virtual Design as a part of the traditional established Failure Mode, Effects, and Criticality Analysis process greatly enhances hazard and risk analysis while ...
Kouroush Jenab, Scot Paterson
doaj   +1 more source

Hierarchical MXene‐Derived NTP/C Nanohybrids for Cryogenic Sodium‐Ion Batteries

Advanced Functional Materials, EarlyView.
A hierarchical MXene‐derived NaTi2(PO4)3/C nanohybrid enables efficient sodium‐ion storage down to −40°C by integrating fast ion–electron transport pathways with an ether‐based electrolyte. The system promotes dominant pseudocapacitive behavior and forms a robust inorganic‐rich SEI, collectively mitigating kinetic and interfacial limitations, thereby ...
M. Sai Bhargava Reddy, Mohammad Zaid, Sayan Das, Sooryadas Sudhakaran, Shampa Aich, Vilas G. Pol   +5 more
wiley   +1 more source

Application of artificial neural networks for the prediction of aluminium agglomeration processes

International Journal of Aviation, Aeronautics, and Aerospace, 2018
Aluminium is universal and vital constituent in composite propellants and typically used to improve performance. Aluminum agglomeration takes place on the burning surface of aluminized propellants, which leads to reduced combustion efficiency and 2P flow
TEJASVI K, Y PYDI SETTY, VEMANA VENKATESWARA RAO, KALYAN CHAKARVARTHY   +3 more
doaj   +1 more source

Coagulative Granular Hydrogels with an Enzyme Catalyzed Fibrin Network for Endogenous Tissue Regeneration

Advanced Healthcare Materials, EarlyView.
Coagulative granular hydrogels are composed of packed thrombin‐functionalized microgels that catalyze the conversion of fibrinogen into a secondary fibrin network, filling the interstitial voids. This bio‐inspired approach stabilizes the biomaterial to match the robustness of bulk hydrogels without compromising injectability, mimicking the initial ...
Zhipeng Deng, Camila B. Tovani, Simona Bianco, Gianni Comandini, Aya Elghajiji, Mina Aleemardani, Roxana Moscalu, Jeremie Zappia, Bianca Fernandes, Olivia Annett, Chrissy L. Hammond, Jason Wong, Dave J. Adams, Fabrizio Scarpa, Michael R. Whitehouse, Annela M. Seddon, James P. K. Armstrong   +16 more
wiley   +1 more source