Results 101 to 110 of about 96,593 (259)

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

INTEGRATING 3D MODELING INTO TECHNICAL DRAWING EDUCATION FOR THE DEVELOPMENT OF SPATIAL THINKING

Journal of Industrial Design and Engineering Graphics
The development of spatial thinking is a key objective in engineering education and technical drawing instruction. Traditional 2D teaching approaches often limit students’ ability to correctly interpret complex geometric relationships.
Ana – Maria TOMA, Oana NECULAI, Irina IGNATESCU-MANEA   +2 more
doaj   +2 more sources

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source

High-Temperature Formability and Friction Regulation Mechanism of TA17 Titanium Alloy with Typical Microstructures. [PDF]

Materials (Basel)
Yan B, Zhang G, Liu X, Yang Y.
europepmc   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source