Results 231 to 240 of about 4,082,360 (307)

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Supply chain carbon reduction considering consumer skepticism and blockchain technology under the cap-and-trade policy. [PDF]

PLoS One
Yuan PP, Wang Q.
europepmc   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Sociotechnical-systems analysis of IoT-AI convergence in cosmetic health. [PDF]

Front Med (Lausanne)
Makhseed A, Arian H, Shuaib A.
europepmc   +1 more source

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

A novel decision analytic model for environmental sustainability challenges using interval-valued complex spherical fuzzy soft sets. [PDF]

Sci Rep
Ali S, Kumam P, Naveed H, Zulqarnain RM, Kumam W, Bamrungsetthapong W, Seangwattana T.   +6 more
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

A Review of Research on the Valorization and Risk Management of Municipal Solid Waste Incineration Bottom Ash. [PDF]

Materials (Basel)
Nan Y, Wang W, Chen H, Guo J, Chen Y, Yuan D.   +5 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source