Results 41 to 50 of about 19,112 (200)
Open Chemistry, 2020 This review addresses a comparison, based on the literature, among nitrile rubber (NBR), ethylene-propylene-diene-monomer rubber (EPDM), and polyurethane (PU) elastomeric heat shielding materials (EHSM).
Amado Javier Carlos Quagliano +4 more
doaj +1 more source
Polymer Engineering &Science, EarlyView.This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan +5 more
wiley +1 more source
Selection of elastomeric membranes for the removal of volatile organics from water [PDF]
, 1993 A wide range of homogeneous elastomeric membranes has been prepared using dicumylperoxide as a general cross-linking agent. The membranes have been used for both equilibrium sorption measurements and steady-state pervaporation experiments to study ...
Mulder, M.H.V. +4 more
core +2 more sources
eXPRESS Polymer Letters, 2007 Ethylene-propylene-diene-graft-polystyrene (EPDM-g-PS) copolymers were synthesized to obtain different structures of graft copolymers with different graft lengths and graft densities. The structure of synthesized EPDM-g-PS copolymers was characterized by
doaj +1 more source
High Voltage, EarlyView.ABSTRACT Low‐voltage cables insulated with silicone rubber were harvested from three locations in the primary containment vessel of a boiling water nuclear power plant (NPP). Subsequently, the cable, which was placed in an ambient environment with a relatively higher temperature and the highest rate, was cut into four shorter ones.
Yoshimichi Ohki +2 more
wiley +1 more source
On the feasibility of watertight face-sealed window-wall interfaces [PDF]
, 2019 Watertightness is still a major source of concern in the performance of the building envelope. Even very small deficiencies can cause a significant amount of water leakage which may result in structural degradation or malfunctioning of the insulation ...
Van Den Bossche, Nathan +1 more
core +2 more sources
eXPRESS Polymer Letters, 2009 Pyrolytic carbon black (PCB) made from used tires was used in ethylene-propylene-diene copolymers (EPDM). The microstructure of PCB was characterized by scanning electron microscopy (SEM). PCB was compounded with EPDM to prepare EPDM vulcanizates.
doaj +1 more source
Polímeros, 2012 Neste trabalho foi estudado o efeito de três agentes na recuperação de resíduos de borracha, copolímero de etileno-propylene-dieno (EPDMR) contendo negro de fumo. Os três agentes preparados foram: EPDM modificado com 1-dodecanotiol (EPDMSDD), EPDM modificado com ácido esteárico (EPDMAE) e EPDM modificado com ácido graxo linolênico (EPDMAG).
Danielli M. Carmo +5 more
openaire +2 more sources
Groundwater Monitoring &Remediation, EarlyView.Abstract Monitoring of fluid parameters during well development, groundwater production, or geothermal operation is essential for the understanding of subsurface and well processes. We developed FluMoMax, a portable fluid monitoring unit, that can measure several physicochemical parameters in real‐time, to monitor fluid characteristics and to enable ...
Lioba Virchow +5 more
wiley +1 more source
Controlled Local Properties in the Same Part with Sintaflex A New Elastomer Powder Material for the SLS Process [PDF]
, 2005 A new powder material for the SLS (Selective Laser Sintering) process was recently released. The material is a result of fruitful research programs involving industry and university.
Boehler, Paul +4 more
core +1 more source