Results 51 to 60 of about 24,352 (243)
eXPRESS Polymer Letters, 2007 Ethylene-propylene-diene-graft-polystyrene (EPDM-g-PS) copolymers were synthesized to obtain different structures of graft copolymers with different graft lengths and graft densities. The structure of synthesized EPDM-g-PS copolymers was characterized by
doaj +1 more source
High Voltage, EarlyView.ABSTRACT Low‐voltage cables insulated with silicone rubber were harvested from three locations in the primary containment vessel of a boiling water nuclear power plant (NPP). Subsequently, the cable, which was placed in an ambient environment with a relatively higher temperature and the highest rate, was cut into four shorter ones.
Yoshimichi Ohki +2 more
wiley +1 more source
Fushe yanjiu yu fushe gongyi xuebaoTo improve the compatibility of natural rubber (NR) and ethylene-propylene-diene terpolymer (EPDM) and enhance the resistance of NR/EPDM blends to hot air aging, radiation-vulcanized NR/EPDM blends were prepared by γ-ray radiation.
SHI Yong +5 more
doaj +1 more source
Time to failure prediction in rubber components subjected to thermal ageing: A combined approach based upon the intrinsic defect concept and the fracture mechanics [PDF]
, 2014 In this contribution, we attempt to derive a tool allowing the prediction of the stretch ratioat failure in rubber components subjected to thermal ageing.
BEN HASSINE, Mouna +5 more
core +6 more sources
Simulation‐Based Material Design for HVDC Cable Accessories
High Voltage, EarlyView.ABSTRACT The worldwide increasing demand for electricity, coupled with the need for more reliable infrastructures and more interconnected networks, has put forward high voltage direct current (HVDC) technologies for energy transmissions. Questions still arise as regards synthetic insulation for cable systems and accessories, as it remains one of the ...
Thi Thu Nga Vu +2 more
wiley +1 more source
Open Chemistry, 2020 This review addresses a comparison, based on the literature, among nitrile rubber (NBR), ethylene-propylene-diene-monomer rubber (EPDM), and polyurethane (PU) elastomeric heat shielding materials (EHSM).
Amado Javier Carlos Quagliano +4 more
doaj +1 more source
On the feasibility of watertight face-sealed window-wall interfaces [PDF]
, 2019 Watertightness is still a major source of concern in the performance of the building envelope. Even very small deficiencies can cause a significant amount of water leakage which may result in structural degradation or malfunctioning of the insulation ...
Van Den Bossche, Nathan +1 more
core +2 more sources
Traditional &Kampo Medicine, Volume 13, Issue 1, April 2026.ABSTRACT Aim One of the effects of Cistanche herb is described in the Chinese Pharmacopoeia as for lack of strength in muscles and bones. However, concrete evidence of this herb for muscle strength has been hardly reported. The present study aimed to clarify the effects of 30% ethanolic extract of Cistanche tubulosa fleshy stem on muscle strength and ...
Jae‐Won Jung, Chihiro Tohda
wiley +1 more source
Polímeros, 2002 A mistura NBR/EPDM apresenta diferentes velocidades de cura, o que resulta na vulcanização heterogênea das fases, isto é, a fase NBR encontra-se em grande parte reticulada enquanto que a fase EPDM encontra-se pouco reticulada ou não-reticulada em casos ...
Marcia G. Oliveira, Bluma G. Soares
doaj +1 more source
Journal of Applied Polymer Science, Volume 143, Issue 8, February 20, 2026.Dynamic vulcanization at higher shear rates refines PA/NBR morphology, reduces domain size, and maintains mechanical performance after reprocessing. ABSTRACT Thermoplastic vulcanizates (TPVs) of polyamide 6 and nitrile butadiene rubber (PA/NBR) present excellent mechanical properties but traditionally suffer from performance loss during re‐melt ...
André Luís dos Santos da Silva +4 more
wiley +1 more source