Results 81 to 90 of about 74,612 (296)
Stiffening Liquid Crystal Elastomers with Liquid Crystal Inclusions
Advanced Materials, EarlyView.Incorporation of low molecular weight liquid crystals (LC) into liquid crystal elastomers (LCE) leads to a significant increase in their stiffness and output work density. Such remarkable stiffening is attributed to nanoscale phase‐separation and the formation of induced‐smectic domains in polydomain and monodomain LC‐LCEs, respectively.
Sahad Vasanji +7 more
wiley +1 more source
React Epoxies with Z6018 Silicone Intermediate for Superior Electrical Resins [PDF]
, 1958 openalex +1 more source
Advanced Materials, EarlyView.It provides an overview of the synthesis of organic/inorganic nanocomposites, spanning from conventional methods to advanced 3D printing techniques. It summarizes key challenges in 3D‐printed nanocomposites and highlights emerging innovations, including 5D printing, AI‐assisted material design, nanoscale additive manufacturing, and sustainable closed ...
Liwen Zhang +8 more
wiley +1 more source
Nickel Hydroxide Catalyzed Bias‐free Photoelectrochemical NH3 Production via Nitrate Reduction
Advanced Materials, EarlyView.A bias‐free photoelectrochemical nitrate reduction reaction with high efficiency and production rate is achieved using a crystalline silicon photocathode with nickel as the catalyst. Performing the PEC NO3RR under alkaline conditions can be self‐activated of the Ni surface by forming Ni(OH)2.
Wonjoo Jin +9 more
wiley +1 more source
A Light‐Driven Closed‐Loop Chemical Recycling System for Polypinacols
Advanced Materials, EarlyView.This study presents a novel strategy for the photochemical closed‐loop recycling of hydroxyl‐rich polymers. Simple bis‐aldehyde precursors are employed to synthesize polypinacols via UV light irradiation. Subsequent depolymerization is achieved under visible light using a cerium‐based photocatalyst, enabling monomer recovery through selective cleavage ...
Ahsen Sare Yalin +3 more
wiley +1 more source
Case Studies in Construction MaterialsThe hot-mix epoxy resin commonly used in the market has insufficient toughness, resulting in cracking of steel bridge deck pavement. To obtain the excellent toughness of hot mix epoxy resin, the collaborative toughen is put forward to overcome the ...
Shuang Shi +3 more
doaj
Modification of (DGEBA) epoxy resin with maleated depolymerised natural rubber
eXPRESS Polymer Letters, 2008 In this work, diglycidyl ether of bisphenol A (DEGBA) type epoxy resin has been modified with maleated depolymerised natural rubber (MDPR). MDPR was prepared by grafting maleic anhydride onto depolymerised natural rubber.
doaj +1 more source
Mechanical properties of epoxy resins and glass/epoxy composites at cryogenic temperatures [PDF]
, 1967 L. M. Soffer, R. Molho
openalex +1 more source
Advanced Materials, EarlyView.A transformative microwave‐driven vapor‐phase sintering strategy enables densification of proton‐conducting electrolytes at 980 °C, reducing the sintering temperature by over 500 °C and addressing a major bottleneck toward PCEC manufacturing. Abstract Protonic ceramic electrochemical cells (PCECs) hold significant promise for efficient power generation
Dongyeon Kim +8 more
wiley +1 more source
Advanced Materials, EarlyView.This study reports a near‐infrared (NIR) luminescent material (Mg2SiO4:1.5%Cr,5%Li) with efficient (EQE = 48%) ultra‐broadband (FWHM ≈ 2413 cm−1 (226 nm)) NIR emission at 960 nm upon blue‐light excitation. This innovation addresses the low efficiency of long‐wavelength (λmax > 900 nm) NIR‐emitting materials due to the radiationless de‐activation and ...
Lei Zhong +11 more
wiley +1 more source