Results 131 to 140 of about 2,468 (164)
Some of the next articles are maybe not open access.
Equal channel angular pressing of Mg-Y alloy
AIP Conference Proceedings, 2019Tribological wear behaviour of Mg-Y alloy in as cast and ECAP’ed condition has been studied using a pin on disk wear testing machine under the load of 10N & 50N with a sliding temperature of 25°,50° and 100°C with a sliding velocity of 0.3 m/s and sliding distance of 3000m. ECAP was done at a temperature of 350°C up to 4 passes using the route Bc.
Chiranth Bellur Prabhakara +3 more
openaire +1 more source
The principles of grain refinement in equal-channel angular pressing
Materials Science and Engineering: A, 2007Abstract Equal-channel angular pressing (ECAP) is a convenient processing tool for introducing very significant grain refinement, typically to the submicrometer level, in a wide range of metals. It is shown by experiment that processing by ECAP produces very similar microstructures in single crystals and in polycrystalline materials.
openaire +2 more sources
Indentation of titanium processed by equal channel angular pressing
Journal of Physics D: Applied Physics, 2008Commercially pure titanium rods were processed by equal channel angular pressing (ECAP) to obtain an ultrafine-grained microstructure. The titanium rods were extruded for 2 passes at 623 K, using three different bending angles of 90°, 120° and 150°. For the bending angle of 90°, the titanium rods were extruded for 4 and 8 passes in addition to 2 passes.
Rong Chen +5 more
openaire +1 more source
Optimum processing parameters for equal channel angular pressing
Mechanics of Materials, 2016Abstract This study aims to explore the optimum processing parameters for minimum strain coefficient of variance in equal channel angular pressing based on the analysis of whole steady zone. In order to design the die correctly, it is important to understand the effect of die geometry and processing parameters on the deformation behavior, strain ...
M.A. Agwa, M.N. Ali, Amal E. Al-Shorbagy
openaire +1 more source
Equal Channel Angular Pressing of Al Alloy AA2219
Advanced Materials Research, 2009Severe plastic deformation processes (SPD) are gaining importance as advanced materials processing techniques and hold immense potential in obtaining ultra fine-grained high strength materials. Among the SPD techniques, Equal channel angular pressing (ECAP) has its own merits to produce materials with ultra fine grains in bulk with better mechanical ...
V. Anil Kumar +4 more
openaire +1 more source
Incremental equal channel angular pressing of sheets
2010This article discusses incremental equal channel angular pressing of sheets.
Rosochowski, Andrzej +3 more
openaire +2 more sources
Equal channel angular pressing of magnesium alloy AZ31
Materials Science and Engineering: A, 2005Abstract Equal channel angular pressing (ECAP) was applied to a wrought magnesium alloy AZ31 for up to 8 passes at temperatures as low as 100 °C. The application of a back pressure was critical in deforming Mg alloys at lower temperatures. Room temperature mechanical properties were obtained by tensile and hardness tests. With increasing ECAP strain,
K. Xia +4 more
openaire +1 more source
Metal Flow at Equal Channel Angular Pressing with Backpressure
Materials Science Forum, 2006In the present paper a flow pattern of aluminum alloy and copper was investigated by grid procedure, using 2D-modeling and experimental data for ECAP using backpressure. The most important parameters that influence upon flow pattern and deformed state of billets were revealed.
openaire +1 more source
Equal Channel Angular Pressing of Metallic Powders
Materials Science Forum, 2003Hyoung Seop Kim +3 more
openaire +1 more source
Influence of Channel Geometry on Superplasticity in Equal-Channel Angular Pressing
Materials Science Forum, 2004Masakazu Kamachi +3 more
openaire +1 more source