Results 161 to 170 of about 87,963 (287)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Review and assessment of policies and practices for spinal cord injury-related health care supplies, services, and mobility equipment reveal wide inequities and inadequacies in Canada. [PDF]

Front Public Health
Warkentin PB, Gregory JH, Athanasopoulos P, Ripat J, Cowley KC.   +4 more
europepmc   +1 more source

Characterization of Aluminized Layers on Inconel‐738 Alloy: Microstructure, Modeling of Aluminizing Kinetics, and Thermal Behavior

Advanced Engineering Materials, EarlyView.
This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe, Tuba Yener, Suayb Cagri Yener, Mourad Keddam, Cuma Bindal   +4 more
wiley   +1 more source

Perceptions of facilitators, barriers and adaptations for provision of obstetric fistula surgery and care: a qualitative descriptive study of service providers in selected hospitals in Busoga sub-region, eastern Uganda. [PDF]

Front Glob Womens Health
Mukasa PK, Kinney M, Mugwanya W, Kivunike A, Menya A, Maniragaba VN, Jackson D.   +6 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Rethinking rehabilitation resources: an amuse-bouche to supply chain management. [PDF]

Front Rehabil Sci
Abdulsalam Y, Abdulsalam AJ, Özçakar L.   +2 more
europepmc   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

Compliance with infection prevention and control practices and associated factors among healthcare workers in Tanzania: Experience from a secondary level-referral hospital. [PDF]

PLoS One
Charles C, Mkonongo L, Masanja D, Edward P, Maruba D, Mwita PF, Nkondo B, Elisha F, Bucheye E, Nyika A, Kalumiana A, Amsi E, Ambikile E, Sirili N, Mollel J, Njau B, Bahegwa R, Banuba D.   +17 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Conserving supplies of personal protective equipment in healthcare facilities during shortages [PDF]

Pandemics happen when new viruses emerge which can infect people easily and spread from person to person in an efficient and sustained way. Pandemics can place extraordinary demands on public health and health care systems as well as on essential ...

core