Results 191 to 200 of about 2,435,644 (344)

Human Engineering Guide to Equipment Design

, 1973
Gordon A. Eckstrand, Harold P. Van Cott, Robert G. Kinkade   +2 more
openalex   +2 more sources

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

WIPP conceptual design report. Addendum J. Support equipment in the high level waste facility of the Waste Isolation Pilot Plant

, 1977
M.J. Rieb, Robert Foley
openalex   +2 more sources

Advancing Wildfire‐Retardant Materials: Engineering Strategies for Direct and Indirect Suppression

Advanced Engineering Materials, EarlyView.
Here, the evolution, ecological impact, and performance of current fire‐retardant materials and suppression strategies are reviewed, offering an engineering perspective to address existing challenges and propose pathways for the development of more effective, scalable, and sustainable solutions to meet the demands of a changing climate. Wildfires cause
Changxin Dong, Samya Sen, Athena Kolli, Stewart G. Wilson, Eric Andrew Appel   +4 more
wiley   +1 more source

High‐Temperature Oxidation of the CrFeNi Medium‐Entropy Alloy

Advanced Engineering Materials, EarlyView.
The oxidation behavior of equiatomic CrFeNi MEA is a key issue that determines this material's suitability for high‐temperature application. The understanding of long‐term behavior is even more crucial than short‐term corrosion effects. The alloy is exposed to synthetic air at 1000, 1050, and 1100 °C for 24, 100, and 1000 h and systematically compared ...
Anna Maria Manzoni, Wencke Mohring, Mike Schneider, Guillaume Laplanche, Sebastian Peter Hagen, Christiane Stephan‐Scherb   +5 more
wiley   +1 more source

AI-Driven Decision Support Framework for Preventing Medical Equipment Failure and Enhancing Patient Safety: A New Perspective. [PDF]

J Multidiscip Healthc
Alkhatib SA, Katmah R, Kosaji D, Afzal SUB, Tariq MH, Simsekler MCE, Ellahham S.   +6 more
europepmc   +1 more source

Combustion Equipment Design Aided by cold Flow Modeling

, 1987
Toshiaki Hasegawa
openalex   +2 more sources

Design and Implementation of a Portal for the Medical Equipment Market: MEDICOM [PDF]

, 2001
Στέργιος Παλαμάς, D. Kalivas, O. Panou-Diamandi, C. Zeelenberg, Chris van Nimwegen   +4 more
openalex   +1 more source

Residual Stress States in Microstructurally Graded PBF–LB/M Austenitic Steel Components

Advanced Engineering Materials, EarlyView.
This study examines microstructurally graded 316L rectangular tube profiles fabricated via PBF–LB/M using a dual‐laser system. A 1 kW top‐hat and a 400 W Gaussian laser create distinct grain sizes and crystallographic texture. Mechanical properties are linked to microstructural evolution driven by processing conditions.
Nico Möller, Florian Loebich, Thomas Wegener, Julia Richter, Jens Gibmeier, Thomas Niendorf   +5 more
wiley   +1 more source

Design and Evaluation Method of a High-Overload Test Device Based on AD-TRIZ. [PDF]

Sensors (Basel)
Zhou P, Zhao L, Liang W, Zhao Y, Li C, Tan F.   +5 more
europepmc   +1 more source