Results 201 to 210 of about 1,051,691 (327)

A Study on Thermal Expansion and Thermomechanical Behavior of Composite Metal Foams

Advanced Engineering Materials, EarlyView.
The coefficient of thermal expansion of steel–steel composite metal foam (S‐S CMF) is shown to be lower than that of bulk stainless steel while its performance under compression demonstrate excellent mechanical stability and strength at all temperatures with gradualsoftening from 400 to 600 °C.
Zubin Chacko, Nigel Amoafo Yeboah, Afsaneh Rabiei   +2 more
wiley   +1 more source

A Study for Reliability Improvement of Passenger Service Equipment using Failure Analysis

, 2016
Bumtaek Roh, Kwang‐Woo Chung
openalex   +2 more sources

Fabrication of Compositionally Graded NiTi Shape Memory Alloy Laminated Composites Through Hot Roll Bonding and its Characterization

Advanced Engineering Materials, EarlyView.
A novel technique for fabricating monolithic functionally graded NiTi shape memory alloy (SMA) laminated hybrid composite has been developed. An excellent metallurgical bonding can be established between two compositionally different NiTi SMAs through spark plasma sintering joining/diffusion bonding followed by hot roll bonding.
Soumya Sinha, Bikas Chandra Maji, Ram Niwas Singh   +2 more
wiley   +1 more source

ANALISIS TOTAL PRODUCTIVE MAINTENANCE DENGAN METODE OVERALL EQUIPMENT EFFECTIVENESS DAN FUZZY FAILURE MODE AND EFFECTS ANALYSIS

, 2017
Supriyadi Supriyadi, Gina Ramayanti, Romi Afriansyah   +2 more
openalex   +2 more sources

THE EFFECT OF THE AMOUNT OF DATA ARRAY ON THE RESULTS OF FORECASTING NETWORK EQUIPMENT FAILURES

, 2021
Ali Myrzatay, Leila Rzayeva, G.A. Uskenbayeva, A.K. Shukirova, Gulnara Abitova   +4 more
openalex   +2 more sources

Fire in the operating room due to equipment failure

Journal of Anaesthesiology Clinical Pharmacology, 2013
Chethan M Koteswara, Rajesh K Lalla
openaire   +4 more sources

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

Advanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag, Funda Kilic, Mrutyunjay Panigrahi, Baris Avar   +3 more
wiley   +1 more source

Maintenance Practice, Causes of Failure and Risk Assessment of Diagnostic Medical Equipment

, 2017
John Kwaku Kutor, Peter Agede, Rashid Haruna Ali   +2 more
openalex   +1 more source

Enhanced Mechanical Properties of Injectable Chitosan–Guar Gum Hydrogel Reinforced with Bacterial Cellulose Nanofibers for Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This study presents the development and characterization of injectable nanocomposite hydrogels based on N‐succinyl chitosan, oxidized guar gum, and bacterial cellulose nanofibers. Emphasizing enhanced mechanical properties and biocompatibility, the hydrogels exhibit fast gelation, improved structural integrity, and reduced swelling. Their potential for
Raimundo Nonato Fernandes Moreira Filho, Pascale Chevallier, Silvia Rodriguez Fernandez, Maud Viallon, Matheus Xavier de Oliveira, Ana Lorena de Brito Soares, Diego Mantovani, Judith Pessoa de Andrade Feitosa, Rodrigo Silveira Vieira   +8 more
wiley   +1 more source

Exploration of the Construction and Application of Knowledge Graph in Equipment Failure

, 2017
Yuan-cheng LU, Wen Yi-jun, Xuan Li, Bing Liu   +3 more
openalex   +2 more sources