Results 81 to 90 of about 1,156,921 (307)

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Production risk management of prawn crackers using fuzzy FMEA and fuzzy AHP methods

Advances in Food Science, Sustainable Agriculture, and Agroindustrial Engineering
Prawn crackers hold a significant position within Indonesia's agro-industrial product landscape. The industrial process involved in their production is fraught with potential risks that could result in substantial losses for companies. PT.
Sri Dharma Cyntya Atmaka, Imam Santoso, Wike Agustin Prima Dania   +2 more
doaj   +1 more source

Effective Maintenance by Reducing Failure-Cause Misdiagnosis in Semiconductor Industry (SI)

International Journal of Prognostics and Health Management, 2015
Increasing demand diversity and volume in semiconductor industry (SI) have resulted in shorter product life cycles. This competitive environment, with high-mix low-volume production, requires sustainable production capacities that can be achieved by ...
Asma Abu-Samah, Muhammad Kashif Shahzad, Eric Zamaï, Stéphane Hubac   +3 more
doaj   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

A Statistical Evaluation Method Based on Fuzzy Failure Data for Multi-State Equipment Reliability

Mathematics
For complex equipment, it is easy to over-evaluate the impact of failure on production by estimating the reliability level only through failure probability.
Jingjing Xu, Qiaobin Yan, Yanhu Pei, Zhifeng Liu, Qiang Cheng, Hongyan Chu, Tao Zhang   +6 more
doaj   +1 more source

Surveys for sensitivity to fibers and potential impacts from fiber induced failures [PDF]

The surveys for sensitivities to fibers and potential impacts from fiber induced failures begins with a review of the survey work completed to date and then describes an impact study involving four industrial installations located in Virginia.
Butterfield, A. J.
core   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

The MOD-OA 200 kilowatt wind turbine generator design and analysis report [PDF]

The project requirements, approach, system description, design requirements, design, analysis, system tests, installation safety considerations, failure modes and effects analysis, data acquisition, and initial performance for the MOD-OA 200 kw wind ...
Andersen, T. S., Bodenschatz, C. A., Eggers, A. G., Hughes, P. S., Lampe, R. F., Lipner, M. H., Schornhorst, J. R.   +6 more
core   +1 more source

An iterative method for the simultaneous optimization of repair decisions and spare parts stocks [PDF]

, 2009
In the development process of a capital good, it should be decided how to maintain it once it is in the field. The level of repair analysis (LORA) is used to answer the questions: 1) which components to repair upon failure, and which to discard, 2) at ...
Basten, R.J.I., Heijden, M.C. van der, Schutten, J.M.J.   +2 more
core   +2 more sources

An investigation into current production challenges facing the Libyan cement industry and the need for innovative Total Productive Maintenance (TPM) strategy [PDF]

, 2011
Purpose - The purpose of this paper is to investigate maintenance and production problems in the cement industry in Libya with particular emphasis on future implementation of Total Productive Maintenance (TPM).
Al-Habaibeh, A, Graisa, M
core   +1 more source