Results 171 to 180 of about 1,808,638 (268)

Optimization of Mix Proportion and Performance Study of Metakaolin-Slag Geopolymer Mortar Based on Orthogonal Experiment. [PDF]

Materials (Basel)
Liang P, Zhu L, Yin R, Gao R.
europepmc   +1 more source

Observer‐Based Adaptive Event‐Triggered Tracking Control for Fuzzy TS Systems With Premise Mismatch

International Journal of Adaptive Control and Signal Processing, EarlyView.
This paper presents an adaptive logistic event‐triggered observer‐based tracking controller for Takagi‐Sugeno fuzzy systems under constrained inputs and network delays. Leveraging a hybrid LMI and Secretary Bird Optimization approach, this strategy significantly minimizes communication overhead and computational burden while ensuring optimal reference ...
Oussama Djadane, Salama Makni, Mourad Kchaou, Ahmed El Hajjaji   +3 more
wiley   +1 more source

Editorial Note: Re-use of laboratory utensils reduces CO2 equivalent footprint and running costs. [PDF]

PLoS One
PLOS One Editors.
europepmc   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Numerical Simulations and Bending Fatigue Experiments of Compensation Ropes Adopted in Highspeed Railway. [PDF]

Materials (Basel)
Zhao Y, Zhao Q, Li F, Zhang H, Du F, Yu X, Zhao A.   +6 more
europepmc   +1 more source

Equivalence of fortifiers [PDF]

The Journal of Pediatrics, 2019
openaire   +2 more sources

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Validation of 3nethra specto, a wearable digital subjective refractor versus conventional subjective refraction for refractive error measurement in young adults: a comparative study. [PDF]

BMJ Open Ophthalmol
Murali K, Hegde N, S A, M V, Agarwal D, Manthri Rangaraj R, Hullur R, Sidiq K, S V.   +8 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Integrating measurement and simulation for evaluation of patient-specific whole-body dosimetry in clinical BNCT. [PDF]

Med Phys
Kakino R, Hu N, Sasaki A, Nojiri M, Yoshino Y, Takeno S, Aihara T, Matsubayashi N, Takata T, Tanaka H, Nihei K, Ono K.   +11 more
europepmc   +1 more source