Results 111 to 120 of about 190,194 (300)
Fabric‐Based Wearable Robotic Exoskeleton Gloves: Advancements and Challenges
Advanced Materials Technologies, EarlyView.This review highlights interdisciplinary technological advances in fabric‐based robotic gloves, focusing on progress in design, fabrication, actuation, sensing, control, and power and energy requirements. It also addresses performance testing and validation, including biomechanical, strength, functional, user experience, and durability assessments, to ...
Ayse Feyza Yilmaz +2 more
wiley +1 more source
Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact
Advanced Materials Technologies, EarlyView.This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt +11 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Here, it is shown that focused ion beam induced deposition (FIBID) using helium and neon ions enables advanced high‐resolution 3D nanoprinting achieving precise multimaterial architectures and engineered internal voids. Thus, FIBID with finely focused noble gas ion species is presented as a unique platform for designing functional nanomaterials for ...
Frances Isabel Allen
wiley +1 more source
The Beauty of Symmetry: Common-mode rejection filters for high-speed interconnects and balanced microwave circuits [PDF]
, 2017 Common-mode rejection filters operating at microwave frequencies have been the subject of intensive research activity in the last decade. These filters are of interest for the suppression of common-mode noise in high-speed digital circuits, where ...
Bonache, Jordi +6 more
core
Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery
Advanced Materials Technologies, EarlyView.Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein +6 more
wiley +1 more source
Magnetic equivalent circuit based permanent magnet characterization
, 2016 This thesis sets forth a permanent magnet characterization fixture and procedure. The work begins with a review of the state of the art in permanent magnet characterization. It then sets forth a new characterization fixture. The proposed system relies on the use of low cost sensors to perform the necessary measurements, which consists of search coils ...
openaire +1 more source
Micro Elastofluidics for Tuneable Droplet Merging
Advanced Materials Technologies, EarlyView.This technical paper provides a proof of concept of fully flexible and stretchable microfluidic technology for tuneable droplet mixing and merging. The phenomenon is justified through theoretical, numerical and experimental studies. ABSTRACT Droplet microfluidics enables precise handling of discrete fluid volumes at the microscale, with broad ...
Uditha Roshan +8 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger +9 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Band‐tail and deep trap states are effectively disentangled through the use of selective alkylamine additives. PA‐driven 2D ordering narrows band tails, while HA enhances halide passivation and Pb coordination to suppress deep traps. A comparative study of their CQD short‐wave infrared (SWIR) photodetectors further reveals whether band‐tail states or ...
Huaying Zhong +14 more
wiley +1 more source
A novel inductive electromagnetic energy harvester for condition monitoring sensors [PDF]
, 2010 As the operation of electrical power networks becomes increasingly sophisticated, the role of condition monitoring is expanding. The burden of implementing additional condition monitoring will be eased if self-powered, fully autonomous sensors can be ...
Fraser, Leigh +2 more
core