Results 151 to 160 of about 156,071 (279)

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Biomechanical Analysis of Mandibular Implant-Supported Overdentures With Different Retention Materials. [PDF]

Int Dent J
Li J, Zhang W, Qu Z, Chen Q, Wang J, Xu J, Zhang X.   +6 more
europepmc   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Carbon Nanotube Hydrogel Electrodes for High-Fidelity Intra-Aural EEG in Wearable Neurotechnology. [PDF]

Sensors (Basel)
Mihai AȘ, Iordache AM, Vereștiuc L, Nacu I, Geman O.   +4 more
europepmc   +1 more source

Equivalent ellipse concept used for determination of endurance limit of porous materials

Metal Powder Report, 1997
openaire   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Accurate iodine quantification and residual error reduction with principal component analysis multimaterial decomposition using spectral CT. [PDF]

Med Phys
Khodajou-Chokami H, Ding H, Molloi S.
europepmc   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Expanding the OMOP common data model to support extracorporeal life support research. [PDF]

JAMIA Open
Rieder C, Zhuk A, Said A, Becker-Pennrich AS, Dietz K, Bělohlávek J, Geppert J, Horvat C, Barbaro RP, Tonna JE, Conrad SA, Broman LM, Reich C, Blacketer C, Brodie D, Alexander PMA, Hoechter DJ.   +16 more
europepmc   +1 more source