Results 141 to 150 of about 1,659,749 (358)

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani   +2 more
wiley   +1 more source

Nanoindentation Criteria for Combinatorial Thin Film Libraries

open access: yesAdvanced Engineering Materials, EarlyView.
Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

open access: yesAdvanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann   +3 more
wiley   +1 more source

Variables in turbine erosion [PDF]

open access: yes, 1970
Study of impact erosion in the operation of turbomachinery is undertaken to predict the results for particular designs. The test program investigates the effects of turbine stator blade shape, rotor blade shape, and variations in test ...
Baughman, J. R., Spies, R.
core   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

open access: yesAdvanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios   +5 more
wiley   +1 more source

THE ROLE OF ENVIRONMENTAL EDUCATION IN PREDICTING ADOPTION OF WIND EROSION CONTROL PRACTICES [PDF]

open access: yes
Logit and ordered probit analyses were used to identify factors associated with reduced tillage adoption, continuous spring cropping, and the number of changes made in response to wind erosion.
Camara, Oumou M.   +2 more
core   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

open access: yesAdvanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi   +2 more
wiley   +1 more source

Sensors measure surface ablation rate of reentry vehicle heat shield [PDF]

open access: yes, 1966
Sensors measure surface erosion rate of ablating material in reentry vehicle heat shield. Each sensor, which is placed at precise depths in the heat shield is activated when the ablator surface erodes to the location of a sensing point.
Russel, J. M., III
core   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

open access: yesAdvanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann   +6 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

open access: yesAdvanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy