Results 81 to 90 of about 119,769 (265)

A STUDY OF SEDIMENT DELIVERY RATIO USING AVSWAT-X IN THE CATCHMENT AREA OF PACAL RESERVOIR OF BOJONEGORO

Journal of Civil Engineering
Recently, the flood intensity that brought by tributary rivers in the catchment area of Pacal reservoir has increased, both in the quantity of runoff and sediment volume.
Bambang Sarwono, Nadjadji Anwar, Zulis Erwanto   +2 more
doaj   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Statistical analysis to examine the influence of thermal aging on hybrid glass epoxy polymer composites with fillers of multi‐walled carbon nanotubes

SPE Polymers
E‐glass fibers are widely preferred due to ease of processing and its low cost, which has substantial scope in the fields of electronics and electrical insulation applications.
K. Sravanthi, V. Mahesh, B. Nageswara Rao, S. P. Jani   +3 more
doaj   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Numerical investigation of erosion response towards a high-head Francis turbine with special emphasis on clearance sizes effect of guide vane

Engineering Applications of Computational Fluid Mechanics
The leakage flow induced by the end clearance of guide vanes in Francis turbines significantly impacts unit efficiency and sediment erosion characteristics.
Longgang Sun, Meng Wen, Shuaihui Sun, Zhuofei Xu, Pengcheng Guo   +4 more
doaj   +1 more source

Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy

Advanced Engineering Materials, EarlyView.
The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche, Marie Münchhalfen, Aditya Srinivasan Tirunilai, Jürgen Schreuer   +3 more
wiley   +1 more source

Long-term mesh erosion rate following abdominal robotic reconstructive pelvic floor surgery: a prospective study and overview of the literature. [PDF]

Int Urogynecol J, 2020
van Zanten F, van Iersel JJ, Paulides TJC, Verheijen PM, Broeders IAMJ, Consten ECJ, Lenters E, Schraffordt Koops SE.   +7 more
europepmc   +1 more source

Enhancing Fatigue Crack Growth Resistance in Heterostructured Aluminum Bimetals by Tailored Interface Design

Advanced Engineering Materials, EarlyView.
Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath, Philip Manuel Pohl, Heinz Werner Höppel   +2 more
wiley   +1 more source

On the Effect of Creep on Local Lattice Orientation in Single‐Crystal Ni‐Based Superalloy Microstructures

Advanced Engineering Materials, EarlyView.
During creep of a single‐crystal Ni‐based superalloy, the overall crystal orientation is observed to remain constant while the microstructure evolves. Despite the lack of macroscopic rotation, small (<1°) rotations are observed on the submicron size scale and are accommodated by counteracting rotations over the scale of several micrometers.
E. J. Payton, E. B. Dursun, G. Eggeler, L. Agudo Jácome   +3 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source