Results 51 to 60 of about 55,668 (311)
High Temperature Materials and Processes, 2017 The directionally solidified eutectic MgAl2O4-Y3Al5O12 crystal was prepared at a pressure of 0.4 MPa of ambient nitrogen gas by the high frequency induction heated floating zone furnace.
Abalı Serkan
doaj +1 more source
Phase behavior and solubility of components of the binary butyric acid – polyethylene glycol-1500 system [PDF]
Известия Саратовского университета. Новая серия: Серия Химия. Биология. ЭкологияA critical review of the literature on the methods of concentration and extraction of biobutyric acid from fermentation solutions has been carried out. The best results of these processes are achieved by combining extraction with salting.
Sheviakhova, Alisa V. +3 more
doaj +1 more source
Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing
Advanced Engineering Materials, EarlyView.This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu +10 more
wiley +1 more source
, 2022 4469 eutectic pairs and their melting temperatures in Celsius, transcribed from "Physical Properties Data Compilations Relevant to Energy Storage I.
Nila Mandal, Qian Yang
core +1 more source
SOME PECULIARITIES OF TECHNOLOGY AND ORGANIZATION OF ALUMINIUM AND ITS ALLOYS RECYCLING
Литьë и металлургия, 2010 Some peculiarities of technology and organization of recycling of aluminium and its alloys are examined. Analysis of peculiarities of the melting technology in rotor furnace and organization of aluminium and its alloys recycling shows that modern ...
A. M. Galushko +6 more
doaj
Frontiers in Materials, 2020 This study aimed at understanding the structure and properties of dual-phase eutectics in ternary, quaternary, and quinary alloys of the Al-Co-Cr-Fe-Ni system. The alloys at case were i) Ni48Fe34Al18, ii) Ni44Fe20Cr20Al16, and iii) Ni34.4Fe16.4Co16.4Cr16.
Daniel Röhrens +7 more
doaj +1 more source
Transient Directional Solidification of Cast Iron: Microstructure Formation, Columnar to Equiaxed Transition and Hardness [PDF]
Materials Research, 2016 A number of applications may require cast iron. Engine cylinder blocks, flywheels, gearbox cases, machine-tool bases may be manufactured by using grey cast iron while bearing surfaces with white cast iron. Thus, understanding the solidification behaviour
Thiago Sartorello Spinola +1 more
doaj +2 more sources
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
, 2022 For sustainable storage of electrical energy, all-organic batteries based on redox-active polymers promise to become an alternative to conventional lithium ion batteries.
Matthias, Uhl +7 more
core +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source