Results 141 to 150 of about 423,821 (335)
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
A method for defining down-wind evacuation areas for transportation accidents involving toxic propellant spills [PDF]
Evacuation areas for accidental spills of toxic propellants along rail and highway shipping routes are defined to help local authorities reduce risks to people from excessive vapor concentrations. These criteria along with other emergency information are
Siewert, R. D.
core +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Deterministic Detection of Single Ion Implantation
Advanced Engineering Materials, EarlyView.Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay +3 more
wiley +1 more source
Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing
Advanced Engineering Materials, EarlyView.This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu +10 more
wiley +1 more source