Results 141 to 150 of about 100,938 (307)
Advanced Functional Materials, EarlyView.Polarity‐matched Zr–MOFs program Nafion's nanoscale morphology during solution casting. Hydrophilic UiO‐66 preserves hydrated pathways, while hydrophobic UiO‐67 increases the proton hopping sites by densifying ionic clusters. Combining both fillers yields a membrane that delivers 176 mS cm−1 conductivity, reaches 1.46 W cm−2 under 200 kPa, and triples ...
Yonghwi Cho +13 more
wiley +1 more source
Chitin‐Derived Carbon‐Metal Functional Materials
Advanced Functional Materials, EarlyView.Functional carbon materials are synthesized from combination of biopolymer (chitin) and iron precursors. The resultant material exhibits superior surface area and adsorptive properties compared to carbon materials synthesized directly from pure chitin.
Herry Fang +7 more
wiley +1 more source
Evaporator Cleaning Studies Evaporator Cleaning Studies • BNFl
, 2020 • Dilute nitric acid (ca. 1.0 M) effectively dissolved sodium aluminosilicate at elevated temperature (90 DC) at an instantaneous rate of 2400 mg/LIh. The solids tested came from the 242-16H Gravity Drain Line. • Caustic dissolution (3 M and 8 M ) proved
core
Advanced Functional Materials, EarlyView.The liposome nanoreactor method enables uniform metal nanoparticle synthesis using the interior as a reaction environment. We demonstrate that peptide sequences and lipid compositions act as a functional molecular switch to control reaction environments in liposome nanoreactors.
Yuya Abe +6 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Schematic illustration of the engineered RN@FDT for multimodal tumor therapy. a) Fabrication of FD&DOX/TFA‐loaded RGD‐NNV (RN@FDT) and the light‐triggered disassemble of RN@FDT. b) After internalized by tumor cells, RN@FDT are disintegrated under NIR‐II laser irradiation to boost PTT and induce cell apoptosis.
Jiahui Zhang +16 more
wiley +1 more source
, 2011 On-line training for the use of experimental equipment: Wordentec thermal evaporator. The resources consists of six Quicktime and Flash videos, covering all stages of the experimental procedure: 1. Introduction to Thermal Evaporators; 2.
Dr Matthew Bryan, The University of Sheffield
core
Advanced Functional Materials, EarlyView.A mechanically programmable hydrogel for tissue engineering is developed by modulating the molecular threading density of poly(ethylene glycol) diacrylate‐β‐cyclodextrin (PEGDA‐β‐CD) polyrotaxane and combining it with β‐CD‐modified gelatin. The polyrotaxane‐guided transition from disordered pores to laminar microstructures enables precise tuning ...
Shiyi Chen +10 more
wiley +1 more source
Bone‐Inspired Recyclable Composites for Damage‐Tolerant Circular Materials
Advanced Functional Materials, EarlyView.Bone‐inspired architected composites are developed by combining osteon‐like reinforcements with a recyclable Elium thermoplastic matrix. The hierarchical architecture redirects cracks and promotes energy dissipation, while enabling recovery of intact, aligned, load‐bearing reinforcement units that retain their original stiffness, revealing a route ...
Alessandro Stagni +4 more
wiley +1 more source
Bio‐Inspired Artificial Ionic Mechanoreceptor
Advanced Functional Materials, EarlyView.A skin‐inspired artificial mechanoreceptor based on ionic interactions is presented for biomimetic tactile sensing. Pressure‐driven ionic redistribution within microfluidic channels generates a self‐powered electrical signal without external bias. The generated waveform exhibits mechanoreceptor‐like temporal features, including overshoot and undershoot,
Mohammad Akbari +4 more
wiley +1 more source