Results 111 to 120 of about 170,516 (304)

Localized fluidization in granular materials: Theoretical and numerical study

, 2016
We present analytical and numerical results on localized fluidization within a granular layer subjected to a local injection of fluid. As the injection rate increases the three different regimes previously reported in the literature are recovered ...
Chareyre, B., Montellà, E. P., Sibille, L., Toraldo, M.   +3 more
core   +2 more sources

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Slow Kinetics of Capillary Condensation in Confined Geometry: Experiment and Theory

, 2001
When two solid surfaces are brought in contact, water vapor present in the ambient air may condense in the region of the contact to form a liquid bridge connecting the two surfaces : this is the so-called capillary condensation.
Bocquet, L., Charlaix, E., Crassous, J., Restagno, F.   +3 more
core   +3 more sources

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Excess Pore Pressure Migration Analysis Due to High Embankment Construction – Case Study East Kalimantan

Journal of the Civil Engineering Forum
A 42-inch pipeline traverses a predominantly flat right-of-way (ROW), running from south to north in East Kalimantan. Adjacent to the ROW, a coal mine concession was located on the western side, while the Mahakam River lies a further 3 km to the east. A
Edwin Lie, Paulus Pramono Rahardjo, Martin Wijaya   +2 more
doaj   +1 more source

Behavior of Nonplastic Silty Soils under Cyclic Loading

The Scientific World Journal, 2014
The engineering behavior of nonplastic silts is more difficult to characterize than is the behavior of clay or sand. Especially, behavior of silty soils is important in view of the seismicity of several regions of alluvial deposits in the world, such as ...
Nazile Ural, Zeki Gunduz
doaj   +1 more source

The Study of Liquefaction Time Stages due to a Short Duration Shaking

Civil Engineering Dimension, 2017
During the 2006 Yogyakarta earthquake, liquefactions were massively found in Opak River, Yogyakarta, Indonesia. Learning from those events, an experimental study of liquefaction using shaking table was performed, especially to investigate the effect of ...
Lindung Zalbuin Mase
doaj   +1 more source

Evolution of excess pore water pressures around monopiles subjected to moderate seismic loading

Soil Dynamics and Earthquake Engineering
The sustained growth of the offshore wind sector is leading to the construction of offshore wind farms in highly seismic regions of the world. Hence, a large proportion of the potential sites may be exposed to liquefaction risk. Monopiles are directly affected by this phenomenon given their preference as a support system for offshore wind turbines over
Español-Espinel, Carlos, Haigh, Stuart, Madabhushi, Gopal S.P., Abadie, Christelle, Go, James, Morrison, Paul R.J.   +5 more
openaire   +3 more sources

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source