Results 141 to 150 of about 831,238 (272)

Impacts of Device Geometry and Layout on Temperature Profile during Large‐Area Photonic Curing

open access: yesAdvanced Engineering Materials, EarlyView.
The study investigates how gate geometry affects peak curing temperature during photonic curing of solution‐processed indium zinc oxide thin‐film transistors. Using 3D simulations and experimental validation, it reveals that larger gate areas and smaller aspect ratios increase curing temperature and thus improve transistor performance. Findings provide
Yasir Fatha Abed   +3 more
wiley   +1 more source

Fractographic Analysis and Fatigue Behavior of Additively Manufactured Ni‐Superalloy Components with Post Processing Heat Treatment and Hot Isostatic Pressing

open access: yesAdvanced Engineering Materials, EarlyView.
A study of mechanical properties and fractography of PBF‐LB/M‐built Inconel 718, performing heat treatments and hot‐isostatic pressing, is presented. Ultimate tensile strength and fatigue behavior are evaluated, examining differences in maximum load behavior, elongation, and regimes of fatigue.
David Sommer   +3 more
wiley   +1 more source

Active Hydrogen for Electrochemical Ammonia Synthesis

open access: yesAdvanced Functional Materials, EarlyView.
This review provides a comprehensive overview of the active hydrogen (H*) for electrochemical ammonia synthesis with particular attention given to the regulation of H* generation and consumption to suppress the competition of hydrogen evolution reaction and enhance the yield, selectivity, and Faradaic efficiency of ammonia.
Guoqiang Gan, Guo Hong, Wenjun Zhang
wiley   +1 more source

Direct Ink Writing of Conductive Hydrogels

open access: yesAdvanced Functional Materials, EarlyView.
This review examines the use of direct ink writing (DIW) for fabricating conductive hydrogels with customizable 3D structures. It outlines the rheological requirements for successful DIW, followed by an exploration of the materials and ink formulations used to impart electronic and/or ionic conductivity to hydrogels while maintaining printability ...
Monica Ho   +6 more
wiley   +1 more source

Fibrous Pb(II)‐Based Coordination Polymer Operable as a Photocatalyst and Electrocatalyst for High‐Rate, Selective CO2‐to‐Formate Conversion

open access: yesAdvanced Functional Materials, EarlyView.
A coordination polymer [Pb(tadt)]n prepared by a microwave‐assisted solvothermal method selectively reduces CO2 into formate under visible light with a high apparent quantum yield of ≈25% at 400 nm. It can function as a pre‐catalyst, along with conductive Ketjen Black, to form an active PbCO3/Pb3(CO3)2(OH)2 mixture that exhibits a high Faradaic ...
Chomponoot Suppaso   +8 more
wiley   +1 more source

Bioresorbable and Wireless Rechargeable Implanted Na‐ion Battery for Temporary Medical Devices

open access: yesAdvanced Functional Materials, EarlyView.
An all‐solid‐state bioresorbable Na‐ion battery is developed, composed entirely of bio‐eliminable materials. In vivo and ex vivo tests confirmed harmless disintegration of this implanted battery. Lifetime of the implanted battery can be precisely controlled by adjusting the dissolvable encapsulation layer's thickness.
Vedi Kuyil Azhagan Muniraj   +8 more
wiley   +1 more source

Designing Metastable P3‐type Layered Negative Electrodes with High Na Vacancy Concentration for High‐Power Sodium‐Ion Batteries

open access: yesAdvanced Functional Materials, EarlyView.
A metastable high‐vacancy concentration layered P3‐type Na0.5Cr0.5Ti0.5O2 negative electrode material has been synthesized from its K analogues P3‐type K0.5Cr0.5Ti0.5O2 using a facile room temperature ion‐exchange method. The P3‐type Na0.5Cr0.5Ti0.5O2 demonstrates a gravimetric capacity of 125 mA h g−1 and high‐rate performance (80% charging in 3 min ...
Alok K. Pandey   +6 more
wiley   +1 more source

Dynamic Micromechanical Characterization of 3D Printed Bone In Vitro Models Manufactured via Vat Photopolymerization

open access: yesAdvanced Functional Materials, EarlyView.
This study presents a novel approach to designing and fabricating high‐porosity 3D‐printed scaffolds using a customized resin. Scaffold geometry, cellular interactions, and mechanical properties are analyzed to demonstrate these engineered bone models.
Sera Choi   +6 more
wiley   +1 more source

Concurrent Interface Passivation and Contact Work Function Tuning in Organic Self‐Aligned Gate Transistors and Complementary Circuits Using Phosphonic Acid Self‐Assembled Monolayers

open access: yesAdvanced Functional Materials, EarlyView.
Self‐aligned gate transistors are developed with a single‐step dielectric passivation and fine‐tuning of source/drain electrode work function using phosphonic acid self‐assembled monolayers (SAM). This transistor architecture minimizes overlap capacitances and access resistance.
Linqu Luo   +16 more
wiley   +1 more source

Home - About - Disclaimer - Privacy