Results 181 to 190 of about 1,498,641 (368)

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

The design process for orthopaedic implants : an introduction. [PDF]

Bone Joint Res
Zdero R, Brzozowski P, Schemitsch EH, Yang I.   +3 more
europepmc   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Localized carbon deposition enables trimming of photonic integrated circuits. [PDF]

Nat Commun
Xu R, Tang Z, McRae L, Varri A, Brückerhoff-Plückelmann F, Ma X, Bankwitz JR, Römer J, Pradip R, Zhang Q, Meyer L, Zhao Z, Dijkstra J, Bhaskaran H, Schröder RR, Pernice WHP, Taheriniya S.   +16 more
europepmc   +1 more source

Fabrication and processing of polymer solar cells: A review of printing and coating techniques

, 2009
F. C. Krebs
semanticscholar   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Angle-Dependent Dip Coating Strategy for Silver Nanostructured Surface Fabrication with Enhanced Fluorescence and Surface-Enhanced Raman Scattering Properties. [PDF]

Biosensors (Basel)
Qi L, Guo K, Ning X, Huang Y, Lu X.
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Development of Optical-Guiding Scintillators with Ultrafine (~12 μm) Uniform Scintillator Cores for High-Resolution X-Ray Imaging. [PDF]

Materials (Basel)
Kamada K, Yoshino M, Nakata Y, Kudo T, Usuki Y, Kutsuzawa N, Kim KJ, Murakami R, Ishizawa S, Yoshikawa A.   +9 more
europepmc   +1 more source

Materials fabrication from Bombyx mori silk fibroin

Nature Protocols, 2011
D. Rockwood, R. C. Preda, Tuna Yücel, Xiaoqin Wang, Michael L. Lovett, D. Kaplan   +5 more
semanticscholar   +1 more source