Results 241 to 250 of about 1,191,977 (372)

RETRACTED: Azizi et al. Cellulose Nanocrystals/ZnO as a Bifunctional Reinforcing Nanocomposite for Poly(vinyl alcohol)/Chitosan Blend Films: Fabrication, Characterization and Properties. <i>Int. J. Mol. Sci.</i> 2014, <i>15</i>, 11040-11053. [PDF]

Int J Mol Sci
Azizi S, Ahmad MB, Ibrahim NA, Hussein MZ, Namvar F.   +4 more
europepmc   +1 more source

Low‐Velocity Penetration Impact Behavior of Triply Periodic Minimal Surface Strut‐Based Lattices

Advanced Engineering Materials, EarlyView.
Triply periodic minimal surface (TPMS)‐based lattices are gaining attention for their multifunctional properties in applications as aeronautics and automotive, which involve low‐velocity impact loading. This work evaluates the low‐velocity penetration impact behavior of five distinct TPMS architectures.
Lucía Doyle, Javier García‐Molleja, Carlos González   +2 more
wiley   +1 more source

L'emploi de l'urée dans le traitement de la caséine utilisée dans la fabrication du papier couché [PDF]

, 1957
G. GÉNIN
openalex   +1 more source

Curved geometric-phase optical element fabrication using top-down alignment. [PDF]

Nanophotonics
Park G, Kim M, Won K, Song SH.
europepmc   +1 more source

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

Advanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag, Funda Kilic, Mrutyunjay Panigrahi, Baris Avar   +3 more
wiley   +1 more source

L'emploi du formaldéhyde dans le traitement de la caséine destinée a la fabrication des peintures [PDF]

, 1959
G. GENIN
openalex   +1 more source

Reliability of the Transmission Line Method and Reproducibility of the Measured Contact Resistance of Organic Thin-Film Transistors. [PDF]

ACS Nano
Wollandt T, Steffens S, Radiev Y, Letzkus F, Burghartz JN, Witte G, Klauk H.   +6 more
europepmc   +1 more source

Fractographic Analysis and Fatigue Behavior of Additively Manufactured Ni‐Superalloy Components with Post Processing Heat Treatment and Hot Isostatic Pressing

Advanced Engineering Materials, EarlyView.
A study of mechanical properties and fractography of PBF‐LB/M‐built Inconel 718, performing heat treatments and hot‐isostatic pressing, is presented. Ultimate tensile strength and fatigue behavior are evaluated, examining differences in maximum load behavior, elongation, and regimes of fatigue.
David Sommer, Ben Truetsch, Cemal Esen, Ralf Hellmann   +3 more
wiley   +1 more source

PCL scaffold with well-defined hierarchical pores effectively controls cell migration and alignment of human mesenchymal stem cells. [PDF]

Sci Rep
Lee SH, Lee J, Kang NU, Cho YS, Heo SC, Park Y, Cho YS.   +6 more
europepmc   +1 more source

Enhanced Mechanical Properties of Injectable Chitosan–Guar Gum Hydrogel Reinforced with Bacterial Cellulose Nanofibers for Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This study presents the development and characterization of injectable nanocomposite hydrogels based on N‐succinyl chitosan, oxidized guar gum, and bacterial cellulose nanofibers. Emphasizing enhanced mechanical properties and biocompatibility, the hydrogels exhibit fast gelation, improved structural integrity, and reduced swelling. Their potential for
Raimundo Nonato Fernandes Moreira Filho, Pascale Chevallier, Silvia Rodriguez Fernandez, Maud Viallon, Matheus Xavier de Oliveira, Ana Lorena de Brito Soares, Diego Mantovani, Judith Pessoa de Andrade Feitosa, Rodrigo Silveira Vieira   +8 more
wiley   +1 more source