Results 41 to 50 of about 19,856 (300)
Situation Analysis of the Feed Manufacturing Industry in Diyarbakır Province
Turkish Journal of Agriculture: Food Science and Technology, 2015 This research was carried out by visiting total 14 feed mills (8 of them are active, 6 of them are passive) in Diyarbakır province in order to get information on feedstuffs, production, quality, technical capacity, marketing, problems and expectations ...
Muzaffer Denli +2 more
doaj +1 more source
Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology
Advanced Engineering Materials, EarlyView.We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham +7 more
wiley +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Feed Mill Worker Dies in Grain Bin [PDF]
On March 15th, 2002, a 41 year-old male feed mill worker died from asphyxiation as a result of entrapment and submersion in flaked corn. The victim had been filling a hopper bottom grain bin with steamed flaked corn on the day of the incident. It appears
core +1 more source
Experimental Investigation on Direct Micro Milling of Cemented Carbide
Micromachines, 2019 Cemented carbide is currently used for various precise molds and wear resistant parts. However, the machining of cemented carbide still is a difficult challenge due to its superior mechanical properties. In this paper, an experimental study was conducted
Xian Wu +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
, 2018 A mathematical model of loading of the nose-free cutting edges of each insert of the face mill with a spiral-stepped cutting scheme was created. It was established that the size of the cut elements depends on the feed magnitude, the design parameters of ...
Melnyk, Oleksandr +7 more
core +1 more source
MILLING FORCE MODELING BASED ON EQUIVALENT TURNING FORCE AND OBLIQUE CUTTING FORCE MODEL (MT)
Jixie qiangdu, 2023 The accuracy of traditional milling force prediction model is low, and it is difficult to provide effective support for the reasonable selection of process parameters in practical production, by synthetically considering the equivalent turning force ...
WU MingZhou +4 more
doaj
Utilizing TiC Cermet in Face-Milling
Bulletin of JSME, 1963 A higher production rate of face-milling will be realized if a more abrasion resistant but less tough tool material can be used without breakage. For this purpose, titanium carbide cermet tool material is studied for utilization in steel face-milling. The main problem is to provide the effective land and the proper rake angle to the cutting edge.
OKUSHIMA, Keiji, HOSHI, Tetsutaro
openaire +2 more sources
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source