Results 231 to 240 of about 1,671,563 (312)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Using the Failure Mode and Effect Analysis Tool to Improve the Automatic Stop Order Process. [PDF]

Glob J Qual Saf Healthc
Al Mardawi GH, Rajendram R, Balharith A, Alomaim A.   +3 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Microtensile Bond Strength and Failure Mode of Different Universal Adhesives on Human Dentin. [PDF]

Int Dent J
Santander-Rengifo F, Carreras-Presas CM, Aroste-Andía R, Hernández-Huamaní E, Gavilán-Chávez P, Cervantes-Ganoza L, Cayo-Rojas C.   +6 more
europepmc   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Automatic failure mode evaluation using non-linear phase contrast correction to improve flow measurement accuracy in cardiovascular magnetic resonance phase contrast imaging. [PDF]

J Cardiovasc Magn Reson
Solana AB, Minderhoud SCS, Wielopolski PA, Hernandez-Tamames JA, Budde RPJ, Helbing WA, Janich MA, Hirsch A.   +7 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Standardization of radiation therapy quality control system through mutual quality control based on failure mode and effects analysis. [PDF]

Radiol Phys Technol
Tanimoto Y, Oita M, Koshi K, Ishiwaki K, Hiramatsu F, Sasaki T, Ise H, Miyagawa T, Maeda T, Okahira S, Hamaguchi T, Kawaguchi T, Funada N, Yamamoto S, Hiroshige A, Mukai Y, Yoshida S, Fujita Y, Nakahira A, Honda H.   +19 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Quality risk management for microbial control in membrane-based water for injection production using fuzzy-failure mode and effects analysis. [PDF]

PeerJ Comput Sci
Zhu L, Liang Y.
europepmc   +1 more source