Results 111 to 120 of about 161,024 (311)

Fatigue of friction stir welded 2024-T351 aluminium alloy

, 2002
Fatigue failure characteristics of friction stir welds in 13mm gauge 2024-T351 plate have been assessed. Failure occurred from either the weld region (nugget/flow arm) or from the material immediately surrounding the weld.
Booth, D., Sinclair, I.
core   +1 more source

Exploring the Potential of Zero‐Dimensional Carbon Nanomaterials in Photoluminescent, Electrochemiluminescent and Electrochemical Sensors

Advanced Materials Interfaces, EarlyView.
Zero‐dimensional carbon nanomaterials are presented as multifunctional platforms linking structure, property, and sensing performance. Surface engineering and heteroatom doping modulate electron‐transfer and luminescent behavior, enabling electrochemical, photoluminescent, and electrochemiluminescent detection. Fundamental design principles, analytical
Gustavo Martins, Jeferson Luiz Gogola, Ava Gevaerd, Cristiane Kalinke, Paulo Roberto de Oliveira, Fabio Roberto Caetano, Bruno Campos Janegitz, Márcio Fernando Bergamini, Luiz Humberto Marcolino‐Junior   +8 more
wiley   +1 more source

Fatigue Damage Assessment Method of Crack-like Discontinuous Zone in Nuclear Reactor Structure

Yuanzineng kexue jishu, 2022
There are a large number of local structural discontinuous zones in the form of cracklike defects in the reactor structure, due to the existence of the stress concentration at weld toes, the fatigue performance of the structure will be remarkably ...
YU Mingda;ZHANG Liping;FU Xiaolong;DU Juan;SHAO Xuejiao;JIANG Lu
doaj  

Light‐Programmable Interfaces: From Molecular Photoswitching to Adaptive Membrane Separations

Advanced Materials Interfaces, EarlyView.
This review advances an interface‐centered framework for light‐responsive membranes, linking molecular photoswitches (azobenzene (AZO), spiropyran (SP), diarylethene (DAE), donor–acceptor Stenhouse adducts (DASA), photoacid) to integration strategies in polymeric, porous, self‐assembled, and mixed‐matrix systems.
Liangliang Zhang, Senlin Gu, Jianyang Zhao, Xiaojuan Hao, Lu Hua Li, Jihua Li, Lingxue Kong   +6 more
wiley   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

The analysis of fatigue crack growth mechanism and oxidation and fatigue life at elevated temperatures [PDF]

Two quantitative models based on experimentally observed fatigue damage processes have been made: (1) a model of low cycle fatigue life based on fatigue crack growth under general-yielding cyclic loading; and (2) a model of accelerated fatigue crack ...
Liu, H. W.
core   +1 more source

Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor

Advanced Materials Technologies, EarlyView.
We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan, Chenzhuo Li, Antonia Georgopoulou, John M. Kolinski, Esther Amstad   +4 more
wiley   +1 more source

Multiaxial fatigue crack path prediction using critical plane concept

Fracture and Structural Integrity, 2015
Prediction of fatigue crack orientation can be an essential step for estimating fatigue crack path. Critical plane concept is widely used due to its physical basis that fatigue failure is associated with certain plane(s).
Jafar Albinmousa
doaj  

Vat Polymerization 3D Printing for Controlled Drug Release Applications

Advanced Materials Technologies, EarlyView.
ABSTRACT Vat polymerization (VP) 3D printing, a light‐based additive manufacturing technique, has emerged as a promising technique for fabricating complex drug delivery systems with high precision and spatial resolution. This layer‐by‐layer manufacturing process enables the creation of intricate geometries and customizable architectures, which are ...
Hafiz Busari, O. Thompson Mefford, M. Aaron Vaughn   +2 more
wiley   +1 more source

Fatigue crack growth in a unidirectional SCS-6/Ti-15-3 composite [PDF]

An investigation was conducted to characterize and model the fatigue crack growth (FCG) behavior of a SCS-6/Ti-15-3 metal matrix composite. Part of the study was conducted using a fatigue loading stage mounted inside a scanning electron microscope (SEM).
Ghosn, Louis, Kantzos, Peter, Telesman, Jack   +2 more
core   +1 more source