Results 41 to 50 of about 8,828 (266)

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

RESEARCH ON FATIGUE CRACK PROPAGATION OF LEAF SPRING UNDER VARIABLE AMPLITUDE LOAD

Jixie qiangdu, 2021
The prediction model of leaf springs fatigue crack growth under variable amplitude loads is mainly Schütz phenomenological model. However, the effect of the crack closure effect on fatigue crack propagation and the relationship between the parameters and
XIANG YuXia, WU ZhiFei
doaj  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Quasi-in-situ observation of fatigue crack growth behavior of friction stir welded 2024-T4 joint

Materials Research Express
This study presents a quasi- in situ observation of the fatigue crack growth behavior in a friction stir welded 2024-T4 joint. The microstructure and fatigue properties of the joint were investigated using electron backscatter diffraction (EBSD ...
Jun Yang, Muhammad Samiuddin, Xianmin Chen, Hao Chen, Zishi Shen, Feng Jin   +5 more
doaj   +1 more source

Fatigue Crack Growth in Thin-Wall Pipes Subjected to Bending [PDF]

International Journal of Advanced Design and Manufacturing Technology, 2019
In this paper, a circumferential external surface flaw in a metallic round pipe under cyclic bending loading is considered. Because of very rapid changes in the geometrical parameters around the crack front region, the mesh generation of this region must
MohammadMahdi Amiri
doaj  

Fatigue Life Prediction for SiC/Al Materials Based on Path Planning Algorithm Considering Residual Stress

Chinese Journal of Mechanical Engineering, 2023
To explore the influence of path deflection on crack propagation, a path planning algorithm is presented to calculate the crack growth length. The fatigue crack growth life of metal matrix composites (MMCs) is estimated based on an improved Paris formula.
Wenqian Shang, Xintian Liu, Xu Wang, Xiaolan Wang   +3 more
doaj   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Study on crack propagation of 42CrMo

Metalurgija, 2019
For the fatigue failure of 42CrMo, the tensile test was performed on the CT specimen at different load ratios using a fatigue tensile tester. Data on the fatigue crack growth rate of the material and the crack tip factor were obtained.
W. C. Pei, J. W. Dong, H. C. Ji, H. Y. Long, S. F. Yang   +4 more
doaj