Results 151 to 160 of about 11,860 (260)

Karl Popper and the Mechanisms of Hydrogen Embrittlement

Advanced Engineering Materials, EarlyView.
Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley   +1 more source

Thermographic approach for a rapid fatigue limit estimation of gears

Gear resistance is an important mechanical aspect to ensure the proper functioning of power transmission systems. It is well known that one of the most dangerous failures in gears refers to tooth root fillet cracks, generally caused by bending fatigue.
Corsaro, Luca, Sesana, Raffaella, Cura, Francesca   +2 more
core   +1 more source

Microstructure‐Controlled Crack Propagation and Fracture Resistance in MoSiBTiC Alloy Revealed by Multiscale Extended Finite Element Method Modeling

Advanced Engineering Materials, EarlyView.
A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du, Takahiro Kaneko, Xinyu Yan, Takahito Ohmura, Kyosuke Yoshimi   +4 more
wiley   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales

Advanced Engineering Materials, EarlyView.
Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik, Alexander Jelinek, Markus Alfreider, Jutta Luksch, Anton Hohenwarter, Florian Schaefer, Christian Motz, Daniel Kiener   +7 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Optimization of the Production of Rubber Compounds Using Mathematical Models

Advanced Engineering Materials, EarlyView.
Rubber compounds were mixed in a batch internal mixer, and symbolic regression was used to derive mathematical models linking recipe and process parameters to ram path, torque, and mixing quality (incorporation, dispersion, distribution). Subsequent optimization with evolutionary algorithms identified operating conditions that reduce specific energy ...
Anke Bardehle, Andreas Limper, Ulrich Giese, Carlos Lucke, Mario Beiner, Christoph Gögelein, Lisa Leuchtenberger‐Engel, Christian Hopmann   +7 more
wiley   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source