Results 31 to 40 of about 2,301,185 (186)
Experimental and theoretical studies of corrosion fatigue in a high strength steel. [PDF]
, 1995 The present work consists of both experimental and theoretical aspects of corrosion fatigue in a high strength steel. Fatigue tests were conducted under fully reversed shear loading in an aerated 0.6M NaC1 solution at pH6, for a silico-manganese ...
Wu, Xiao Dong
core +6 more sources
Engineering Transactions, 2014 A proposition of an energy-based hypothesis of material effort for isotropic materials exhibiting strength-differential (SD) effect, pressure-sensitivity and Lode angle dependence is discussed. It is a special case of a general hypothesis proposed by the
M. NOWAK +3 more
doaj +1 more source
Effect of Corrosion on the High Cycle Fatigue Strength of Martensitic Stainless Steel X12CrNiMoV12-3 [PDF]
, 2012 This paper addresses the effects of corrosion on the high cycle fatigue (HCF) strength of a high mechanical strength martensitic stainless steel (X12CrNiMoV12-3) that is used in aeronautic applications. HCF tests (between 105 and 107 cycles) were carried
PALIN-LUC, Thierry +4 more
core +1 more source
Mathematical Foundations of Limit Criterion for Anisotropic Materials
Archives of Metallurgy and Materials, 2013 Artykuł przedstawia nową propozycję kryterium stanu granicznego dla anizotropowych ciał stałych wykazujących różną wytrzymałość przy rozciąganiu i ściskaniu.
Ostrovvska-Maciejewska J. +2 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2023 Rail corrosion is one of the causes of rail breaks. The relationship between rail corrosion state and fatigue strength is still unclear. Therefore, to accurately estimate the fatigue strength of corroded rails, the prediction method for fatigue strength ...
Jun MIZUTANI +3 more
doaj +1 more source
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation [PDF]
, 2014 The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated.
SIDHOM, Habib +4 more
core +1 more source
Fatigue Strength Characteristics of High-Strength Steel
JSME international journal. Ser. 1, Solid mechanics, strength of materials, 1989 In order to clarify the fatigue strength charactaristics of low alloy steels which were strengthed by tempering at low temperature (150∼200°C) after conventional quenching treatment and/or carburizing in generated gas, rotating bending fatigue tests were conducted in laboratory air and dry air using smoothened specimens with 8 mm diameter.
EMURA, Hideki, ASAMI, Katsutoshi
openaire +3 more sources
Sensors, 2022 Fatigue can be classified as peripheral or central depending on the extent of its effects. Muscle strength reduction, associated with the appearance of fatigue during running, produces kinetics and kinematics modifications which could lead to an ...
Alberto Encarnación-Martínez +5 more
doaj +1 more source
Investigation the Creep-Fatigue Behavior and A.C. Electrical Conductivity of AA 6061 Under Ultrasonic Peening [PDF]
Engineering and Technology Journal, 2019 Ultrasonic peening is an innovative surface improvement process used to increase the resistance of aircraft metals and enhance high cycle fatigue life. The process creates residual compressive stresses deep into part surfaces.
Hussain Al-Alkawi +2 more
doaj +1 more source
Very high cycle fatigue of copper: Evolution, morphology and locations of surface slip markings [PDF]
, 2014 The surfaces of commercially pure polycrystalline copper specimens subjected to interrupted 20 kHz fatigue tests in the very high cycle fatigue regime were investigated.
VALES, Fréderic +4 more
core +1 more source