Results 101 to 110 of about 28,709,098 (187)
Some of the next articles are maybe not open access.
Fault Diagnosis and Fault Model Aliasing
IEEE Computer Society Annual Symposium on VLSI: New Frontiers in VLSI Design (ISVLSI'05), 2005During fault diagnosis, the existence of equivalent faults, or faults that are not distinguished by the test set applied to the circuit, can create ambiguity as to the location of a defect. This happens if the circuit-under-test produces a response that matches the circuit response in the presence of two faults in different locations of the circuit ...
Irith Pomeranz +2 more
openaire +2 more sources
Fault modeling and fault equivalence in CMOS technology
Journal of Electronic Testing, 1991The need for greater reliability in the fault coverage of test sequences for VLSI circuits has led to the proposal for more accurate fault models and test pattern generation tools. Such improvements bring about a large increase in the fault list to be considered and in the CPU time needed to generate the test.
Marie-Lise Flottes +2 more
openaire +1 more source
EAGE Conference on Petroleum Geostatistics, 2007
Although faults traditionally have been modelled as membrane-like surfaces, the flow pattern through a fault is affected in a volumetric region. The physical properties of the fault rock will be different from what they were prior to the faulting process.
Skorstad, Arne +4 more
openaire +1 more source
Although faults traditionally have been modelled as membrane-like surfaces, the flow pattern through a fault is affected in a volumetric region. The physical properties of the fault rock will be different from what they were prior to the faulting process.
Skorstad, Arne +4 more
openaire +1 more source
IEEE transactions on power electronics, 2019
This paper investigates open-phase fault modeling and fault-tolerant control (FTC) of dual three-phase permanent magnet synchronous machines (DT-PMSMs).
Guodong Feng +4 more
semanticscholar +1 more source
This paper investigates open-phase fault modeling and fault-tolerant control (FTC) of dual three-phase permanent magnet synchronous machines (DT-PMSMs).
Guodong Feng +4 more
semanticscholar +1 more source
IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems, 2005
Traditionally, digital testing of integrated semiconductor circuits has focused on manufacturing defects. There is another class of failures that happens due to circuit marginalities. Circuit-marginality failures are on the rise due to shrinking process geometries, diminishing supply voltage, sharper signal-transition rates, and aggressive styles in ...
Kundu, S +3 more
openaire +2 more sources
Traditionally, digital testing of integrated semiconductor circuits has focused on manufacturing defects. There is another class of failures that happens due to circuit marginalities. Circuit-marginality failures are on the rise due to shrinking process geometries, diminishing supply voltage, sharper signal-transition rates, and aggressive styles in ...
Kundu, S +3 more
openaire +2 more sources
IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems, 1991
A fault model for programmable logic arrays (PLAs) is discussed that handles four classes of faults: multiple stuck-at faults, multiple bridging faults, multiple crosspoint faults, and faults due to breaks in lines. It is shown that a test that detects all multiple crosspoint faults also detects all multiple stuck-at faults, multiple bridging faults ...
Michiel M. Ligthart, Rudi J. Stans
openaire +1 more source
A fault model for programmable logic arrays (PLAs) is discussed that handles four classes of faults: multiple stuck-at faults, multiple bridging faults, multiple crosspoint faults, and faults due to breaks in lines. It is shown that a test that detects all multiple crosspoint faults also detects all multiple stuck-at faults, multiple bridging faults ...
Michiel M. Ligthart, Rudi J. Stans
openaire +1 more source
Pinhole Defect Characterization and Fault Modeling for STT-MRAM Testing
IEEE European Test Symposium, 2019The STT-MRAM manufacturing process involves not only traditional CMOS process steps, but also the integration of magnetic tunnel junction (MTJ) devices, the data-storing elements.
Lizhou Wu +8 more
semanticscholar +1 more source
On Testing Output Faults in the McClusky Fault Model
J. Autom. Lang. Comb., 2012Journal of Automata, Languages and Combinatorics, Volume 17, Number 1, 2012, 3 ...
Ulrike Brandt, Hermann K.-G. Walter
openaire +1 more source
Fault modeling and test generation methods for complex digital circuits
Modeling of systems and processesIt is shown that the process of determining the serviceability of any logic block or microcircuit as a whole consists in monitoring its parameters at the output or some other points available for measurement and comparing them with the required ones when
Svetlana Sazonova +3 more
semanticscholar +1 more source

