Results 261 to 270 of about 32,856 (312)

Genomic profiling of ESBL/AmpC-producing <i>Escherichia coli</i> from backyard poultry: resistome, virulome, plasmidome, and CRISPR-Cas insights. [PDF]

Front Microbiol
Nagaraja PK, Mitra SD, Murugesan D, Muninarayanaswamy PKA, Geddam S, Venugopal N, Tewari R, Ramamurthy AS, Skariah S, Nayakvadi S, Shome BR, Shome R.   +11 more
europepmc   +1 more source

Accuracy of Patient‐Reported Exposure to New Psychoactive Substances and Other Illicit Drugs in Australian Emergency Departments: Findings From the Emerging Drugs Network of Australia

Drug and Alcohol Review, Volume 45, Issue 5, July 2026.
ABSTRACT Introduction New psychoactive substances (NPS) present a unique challenge in clinical, public health and drug‐policy contexts. Continued diversity, unknown potency and often unintentional exposure can limit the accuracy of self‐reported data.
Marjan J. Nijmeijer, Jennifer L. Smith, Courtney Weber, Bas W. J. Bens, Daniel M. Fatovich, Shaun L. Greene, Jennifer L. Schumann, Paul Dessauer, Rebekka Syrjanen, Katherine Z. Isoardi, Keith Harris, Sam Alfred, Viet Tran, Ewoud ter Avest   +13 more
wiley   +1 more source

A Virtual Heat Flux Method for Simple and Accurate Neumann Thermal Boundary Imposition in the Material Point Method

International Journal for Numerical Methods in Engineering, Volume 127, Issue 12, 30 June 2026.
ABSTRACT In the material point method (MPM), accurate enforcement of thermal boundary conditions, particularly convective heat flux boundaries, is crucial for the reliable simulation of thermally coupled multiphysics processes, such as natural heat‐convection phenomena on Earth.
Jidu Yu, Jidong Zhao
wiley   +1 more source

Reinforcement of Novel PLA/17-4 PH Stainless Steel Hybrid Structures Fabricated by FDM: The Effects of Layer Configuration, Infill Density and Pattern. [PDF]

Polymers (Basel)
Ötüken R, Alparslan C, Erhan MF, Bayraktar Ş.   +3 more
europepmc   +1 more source

Development of Vertical Wind Turbine Blades Using 4D Printing of Composites

Polymer Composites, Volume 47, Issue 12, Page 10966-10975, 20 June 2026.
Vertical axis wind turbine: White blade: Commercial. Black blade: Composite. ABSTRACT This paper presents the procedure to make vertical wind turbine blades using the technique of 4D printing of composites (4DPC). The blades are made using carbon/epoxy composite materials with a fiber volume fraction of about 60%.
Emad Fakhimi, Suong Van Hoa
wiley   +1 more source

The Use of 3D Printing Technology in Rehabilitation for Adults Living With Neurological Conditions: Scoping Review. [PDF]

JMIR Rehabil Assist Technol
Aggerwal S, Lalani Z, O'Neil J.
europepmc   +1 more source

Enhancing the Performance of 3D‐Printed Polyamide Composites Through Pre‐ and Post‐Processing Methods

Polymer Composites, Volume 47, Issue 11, Page 10002-10017, 10 June 2026.
FDM‐printed polyamide composites and post‐processing by annealing. ABSTRACT In this study, composite filaments with a short carbon fiber (CF) reinforced polyamide 612 (PA612) were produced using the FDM method at three different raster angles (0°, ±45°, 90°).
Busra Eyri, Yusuf Yagci, N. Gamze Karsli, Taner Yilmaz   +3 more
wiley   +1 more source

Aquaporin-1 upregulation is associated with scleral remodeling during myopia development in mice. [PDF]

Am J Transl Res
Zhang W, Cheng Y, Wu J, Jia X, Gao H, Yan J, Li W, Zhang C, Wang X, Gao J.   +9 more
europepmc   +1 more source

Effect of print orientation on the dimensional accuracy of three-dimensional-printed complete denture models: A comparative analysis of VAT photopolymerization and fused deposition modeling technologies. [PDF]

J Indian Prosthodont Soc
Chandraker NK, Chander GN, Dubey RK.
europepmc   +1 more source

Insights into 3D-printed TiO₂-based architectures for photocatalytic and non-catalytic applications. [PDF]

RSC Adv
Theja VCS, Karthikeyan V, Guo Y, Yeung CS, Choudhary S, Kannan V, Assi DS, Saianand G, Lee DE, Anantha Iyengar G, Roy VAL.   +10 more
europepmc   +1 more source