Results 251 to 260 of about 106,769 (350)

Ballistic Performance and Energy Dissipation Mechanisms of Epoxy Composites Reinforced with Raffia Fabric Under 9 mm Impact. [PDF]

Polymers (Basel)
Silva DS, Junio RFP, Bentes EM, Lopes TJ, Marchi BZ, Monteiro SN.   +5 more
europepmc   +1 more source

Experimental Study on Polymer–Polymer Interfacial Thermal Resistance

Macromolecular Theory and Simulations, Volume 34, Issue 2, March 2025.
Interfacial thermal resistance (ITR) in polymer–polymer interfaces is experimentally measured in this paper by the multi‐layered bulk sample approach. Based on numerical simulation and experimental verification, new techniques of layer‐overlapping samples are developed.
Yinfeng Xia, Takushi Saito, Tatsuya Kawaguchi   +2 more
wiley   +1 more source

Green Fiber-Reinforced Laminates: Styrene-Free UPe with VTES-Functionalized ZrO₂ and Flax Fabrics. [PDF]

Polymers (Basel)
Mijatov S, Rančić M, Kovačević T, Vujančević J, Pavlović VB, Gržetić JD.   +5 more
europepmc   +1 more source

Wear‐Mode‐Dependent Tribological Performance of Glass Fiber‐Reinforced Epoxy Composites Modified With Graphene Nanoplatelets

Polymer Composites, EarlyView.
Graphical representation of the wear‐mode‐dependent tribological behavior of graphene nanoplatelet (GNP) modified glass fiber‐reinforced epoxy composites, highlighting the distinct mechanisms governing dry sliding wear and solid particle erosion. ABSTRACT Glass fiber‐reinforced epoxy composites are widely used in structural applications where surface ...
Elif Gültürk, Ruşin Ak, Tunay Fatma Angin   +2 more
wiley   +1 more source

Nano-Engineered Sandwich Interlayers for Simultaneous Functionalization and Delamination Resistance in CFRPs. [PDF]

Polymers (Basel)
Ji P, Zhang Y, Ou Y, Li J, Mao D.
europepmc   +1 more source

Assessing and Quantifying Variability Across Vacuum‐Assisted Resin Infusion Variants for Aerospace‐Grade Composite Manufacturing

Polymer Composites, EarlyView.
Radar‐plot comparison of consolidation quality and flexural performance of composite laminates manufactured by six vacuum‐infusion routes, evaluated at the resin‐inlet and vacuum‐port regions. ABSTRACT Conventional vacuum‐assisted resin transfer molding (C‐VARTM) is recognized as a cost‐effective resin infusion technique for manufacturing large‐scale ...
Ilhan Kahraman, Nilperi Uysal, Çağlar Subaşı, Selin Dursun, Muhammet İskender, Özgü Çalın, Uğur Şimşir, Hatice S. Sas, A. Tuğrul Seyhan   +8 more
wiley   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Study on Fatigue Crack Propagation Behavior of Fiber/Al-Li Laminates Under Typical Overload. [PDF]

Materials (Basel)
Meng W, Tan J, Li S, Huang X, Wang J.
europepmc   +1 more source

Bioinspired Microcavities Enhancing the Interface of Fe-Carbon Fiber-Reinforced Polymer. [PDF]

Materials (Basel)
He L, Wang L, Cui G, Zhang W, Chen M, Hou J, Cui C.   +6 more
europepmc   +1 more source

Optimal Design of CFRP Railway Carbody Laminates via Multi-Criterion Fiber Orientation Sensitivity. [PDF]

Materials (Basel)
Cascino A, Meli E, Rindi A.
europepmc   +1 more source