Results 121 to 130 of about 2,318,807 (308)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

The Results of the Laboratory Study on the Separating Fiber Flax Seed Balls when Combing the Standing Plants with a Single-Rotor Comb-Dresser

Инженерные технологии и системы
Introduction. The low purity of combing flax seed balls with flax harvesters is a problem for the technological operation when harvesting fibre flax.
Sergey V. Solovyov, Viktor G. Chernikov, Roman A. Rostovtsev, Vladislav Yu. Romanenko   +3 more
doaj   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

Evaluation of the Thermophysiological Comfort Properties of Single-Knit Jersey Fabrics

Advances in Materials Science and Engineering
The thermal and physiological comfort of fabric has emerged as a priority over service life and perceived value in today’s apparel industry. The balance between thermal and physical sensations of fabrics profoundly influences consumer perceptions of ...
Derseh Yilie Limeneh, Kalavathy Rajan, Brendan Kelly, Addisu Ferede Tesema, Kelem Tiessasie Yilma, Noureddine Abidi, Zelalem Adane Alemar   +6 more
doaj   +1 more source

Orders and fibering

Groups, Geometry, and Dynamics
In 2018, Kielak gave a virtual fibering criterion for RFRS groups. In this paper, we present a simpler proof of this.
Boris Okun, Kevin Schreve
openaire   +2 more sources

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Fabrication and Characterization of Polyvinyl Alcohol-Jute Cellulose Nanocrystals Composite Films for Packaging Application

Advances in Polymer Technology
The increasing demand for sustainable packaging alternatives has driven research into substitutes for petroleum-based plastics. This study develops eco-friendly composite films by incorporating tetrabutylammonium fluoride and dimethyl sulfoxide extracted
Shamsuzzaman Sheikh, Kazumasa Hirogaki, Koji Nakane   +2 more
doaj   +1 more source

Dissemination, resuspension, and filtration of carbon fibers [PDF]

, 1980
Carbon fiber transport was studied using mathematical models established for other pollution problems. It was demonstrated that resuspension is not a major factor contributing to the risk.
Elber, W.
core   +1 more source