Results 101 to 110 of about 387,141 (296)

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Mechanical and Thermal Performances of Banana Fiber–Reinforced Gypsum Composites

International Journal of Polymer Science
This study investigates the use of alkali-treated banana fibers at different weight percentages (0%, 4%, 6%, 8%, 16%, and 24%) as natural reinforcement in gypsum, aiming to assess their effects on the physical, mechanical, thermal, and morphological ...
Md. Abdur Rouf, Md. Rubel Alam, Shah Alimuzzaman Belal, Yeasin Ali, Md Zillur Rahman   +4 more
doaj   +1 more source

Towards Low Cost Coupling Structures for Short-Distance Optical Interconnections [PDF]

, 2007
The performance of short distance optical interconnections in general relies very strongly on coupling structures, since they will determine the overall efficiency of the system to a large extent.
Alajoki, T., Blanc, D., Destouches, N., Franc, J., Hendrickx, N., Karioja, P., Thienpont, H., Van Daele, P., Van Erps, J.   +8 more
core   +3 more sources

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

Advanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu, Timon Steinhoff, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Christian Klose, Ludger Overmeyer, Hans‐Jürgen Maier, Nina Merkert   +8 more
wiley   +1 more source

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Modification of Wood Fiber for Use in Cement Board

IOP Conference Series: Materials Science and Engineering, 2017
When ordinary Portland cement is used for wood fiber cement (WFC) board, the setting time is too long, even hard to solidify. Three methods can be used for wood fiber modification, i.e., soaking in water, treated with alkali solution and coated with some substances on the fiber surface.
F Q Han, X Tan, F Q Zhao
openaire   +1 more source

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

Advanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang, Annett Wollmann, Thomas Gimpel, Alfred P. Weber   +3 more
wiley   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Barnes Hospital Bulletin [PDF]

, 1975
https://digitalcommons.wustl.edu/bjc_barnes_bulletin/1109/thumbnail ...

core   +1 more source