Results 71 to 80 of about 157,873 (288)

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Viscoelastic Equivalent Creep Behavior and Its Influencing Factors of Basalt Fiber-Reinforced Asphalt Mixture under Indirect Tensile Condition

Advances in Materials Science and Engineering, 2021
The aim of this study is to further investigate the effect of different basalt fiber (BF) factors on the viscoelastic equivalent creep behavior of fiber-reinforced asphalt mixture (FRAM) under indirect tensile (IDT) condition.
Xiaoyuan Zhang, Yu Zhang, Yichun Wu, Peng Xia   +3 more
doaj   +1 more source

Automatic glass fiber length measurement for discontinuous fiber-reinforced composites [PDF]

, 2018
Severe fiber breakage occurs in injection molding, affecting the mechanical performance of discontinuous fiber-reinforced composites. Accurate measurement of the residual fiber length distribution is crucial to experimentally investigate the physics of ...
Zanini F., Giusti R., Lucchetta G.
core   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Developing JMP and VBA Add-Ins for Finite Mixture Modeling of Cotton Fiber Length Distribution

Fibers
In this study, software add-ins were developed and presented to allow data processing and statistical analysis of the unique shape of cotton fiber length distribution.
Mourad Krifa, Vinusha Garlapati, Vikki B. Martin, Neha Kothari   +3 more
doaj   +1 more source

Correlation between Pod Shape Traits and Its Fiber Quality of Wild Calotropis Gigantea

Journal of Natural Fibers, 2017
Seed fiber in the Calotropis gigantea (C. gigantea) pods is the most valuable component and can be developed into textile material. Cultivating high-yield and high-quality seed fibers for C.
Yumei Cui, Longdi Cheng, Xiaohong Shan, Wenhong Fan   +3 more
doaj   +1 more source

A technique for the measurement of reinforcement fibre tensile strength at sub-millimetre gauge lengths [PDF]

, 2001
The strength of composite reinforcement fibres is normally measured on samples of much greater length than the actual residual fibre lengths found in many composite materials.
Kalinka, G., Kalinka, Gerhard, Thomason, J.L.   +2 more
core   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source