Results 91 to 100 of about 12,157 (351)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Comparative analysis of the DFB fiber laser and fiber-optic interferometric strain sensors
, 2007 The DFB fiber laser strain sensor is shown to provide an improvement in the minimum detectable length change by a factor of 275 at 2 kHz for an applied strain when compared with an interferometric sensor interrogated by at equivalent DFB laser.
C. K. Kirkendall +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
We have constructed fiber-optic sensors to measure temperature and strain by combining the properties of fiber Bragg gratings with the fluorescent lifetimes of various doped fibers.
Wade, Scott A. +4 more
core +1 more source
Interfacial and durability aspects of extrinsic Fabry-Perot interferometric sensors in carbon fibre composites [PDF]
, 2003 This thesis is concerned with the interfacial and durability aspects of Extrinsic Fabry- Perot Interferometric (EFPI) sensors embedded in carbon fibre reinforced composites.
Etches, J A
core
Review of long period fiber gratings written by CO2 laser
, 2010 This paper presents a systematic review of long period fiber gratings (LPFGs) written by the CO2 laser irradiation technique. First, various fabrication techniques based on CO2 laser irradiations are demonstrated to write LPFGs in different types of ...
Yiping Wang, Wang, Yiping
core +1 more source
Fabrication of rGO-GO Long Period Fiber Grating Using Laser Reduction Method
IEEE Photonics Journal, 2017 A laser-reduction technique is investigated to fabricate a novel long period fiber grating (LPFG), whose period is a section of graphene oxide (GO) and reduced graphene oxide (rGO) films on a side polished fiber.
Liheng Chen +9 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Investigation of shock waves in explosive blasts using fibre optic pressure sensors
, 2005 The published version of this article may be accessed at the link below. Copyright @ IOP Publishing, 2006.We describe miniature all-optical pressure sensors, fabricated by wafer etching techniques, less than 1 mm(2) in overall cross-section with rise ...
Pichugin, AV +29 more
core +1 more source