Results 81 to 90 of about 61,629 (267)
BMC Cell Biology, 2008 Background The fibre type attributes and the relationships among their properties play an important role in the differences in muscle capabilities and features. Comprehensive characterisation of the skeletal muscles should study the degree of association
Rueda Julia +4 more
doaj +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Journal of King Saud University: Engineering Sciences, 2019 Development of ecofriendly biocomposites to replace non-biodegradable synthetic fibre composites for optimum performances is the main objective of this study.
S.I. Durowaye +3 more
doaj +1 more source
Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions
Advanced Engineering Materials, EarlyView.This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi +5 more
wiley +1 more source
Aerospace, 2018 Recycling carbon fibre is crucial in the reduction of waste from the increasing use of carbon fibre reinforced composites in industry. The reclaimed fibres, however, are usually short and discontinuous as opposed to the continuous virgin carbon fibre. In
Barbara Tse +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan +4 more
wiley +1 more source
Advances in Materials Science and Engineering, 2018 The use of the polypropylene fibre and glass fibre with different volume fractions to improve the mechanical properties of peach shell lightweight concrete was investigated in this study. The volume fractions of 0.25%, 0.50%, and 0.75% were used for each
Fan Wu +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source