Results 61 to 70 of about 213,170 (262)

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Very Fast Field Oriented Control for Permanent Magnet Hysteresis Synchronous Motor

Iranian Journal of Electrical and Electronic Engineering, 2006
In this paper, a new field oriented control scheme with maximum torque for permanent magnet hysteresis synchronous (PMHS) motor has been presented. Vector control method provides significant improvement to the dynamic performance of ac motors but in this
Lesani, Darabi, Nasiri Gheidari, Tootoonchian   +3 more
doaj  

Transient Energy Efficiency Analysis of Field Oriented Induction Machines

IEEE Access, 2017
An open loop control law for stator d- and q-axis currents in a rotor field oriented induction machine are derived in the form of analytical functions of time and used to study how energy losses during speed transients can be minimized.
Siby Jose Plathottam, Hossein Salehfar
doaj   +1 more source

Karl Popper and the Mechanisms of Hydrogen Embrittlement

Advanced Engineering Materials, EarlyView.
Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley   +1 more source

Analysis and Compensation of Phase Current Measuring Error Caused by Sensing Resistor in PMSM Application

Sensors
Field Oriented Control (FOC) effectively realizes independent control of flux linkage and torque, and is widely used in application of Permanent Magnet Synchronous Motor (PMSM).
Xin Cheng, Jinfeng Hu, Ye Yu, Rougang Zhou, Qiang Yu   +4 more
doaj   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Energy Optimization of Field Oriented Six-Phase Induction Motor Drive

Advances in Electrical and Computer Engineering, 2011
This paper deals with the efficiency optimization of Field Oriented Control (FOC) of a six-Phase Induction Motor (6PIM) by adaptive flux search control.
KABOLI, S., RAHMATI, A., TAHERI, A.
doaj   +1 more source

PASTA‐ELN: Simplifying Research Data Management for Experimental Materials Science

Advanced Engineering Materials, EarlyView.
Research data management faces ongoing hurdles as many ELNs remain complex and restrictive. PASTA‐ELN offers an open‐source, cross‐platform solution that prioritizes simplicity, offline access, and user control. Its in tuitive folder structure, modular Python add‐ons, and open formats enable seamless documentation, FAIR data practices, and easy ...
S. Brinckmann, G. Winkens, R. Schwaiger
wiley   +1 more source