Results 121 to 130 of about 285,820 (289)

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

open access: yesAdvanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe   +6 more
wiley   +1 more source

Rotary 3D Printing With Integrated Electroplating

open access: yesAdvanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria   +5 more
wiley   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

open access: yesAdvanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone   +11 more
wiley   +1 more source

THE APPARATUS FOR ALIGNMENT OF THE PHOTOMETRIC LAMP FILAMENT

open access: yesПриборы и методы измерений, 2015
During photometric measurements involving the use of photometric lamps it is necessary that the filament of lamp takes a strictly predetermined position with respect to the photodetector and the optical axis of the photometric setup.
V. A. Dlugunovich   +4 more
doaj  

Intermediate Resistive State in Wafer‐Scale Vertical MoS2 Memristors Through Lateral Silver Filament Growth for Artificial Synapse Applications

open access: yesAdvanced Functional Materials, EarlyView.
In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa   +19 more
wiley   +1 more source

Mathematical modelling of the half-sarcomere from a human skeletal muscle [PDF]

open access: yes
The character of the functional output of a motor unit within skeletal muscle has been linked experimentally to the proteins found in the sarcomere, the smallest contractile unit of muscle fibre.
Guest, Kay P.
core  

Integration of Low‐Voltage Nanoscale MoS2 Memristors on CMOS Microchips

open access: yesAdvanced Functional Materials, EarlyView.
This article presents the first monolithic integration of nanoscale MoS2‐based memristors into the back‐end‐of‐line of foundry‐fabricated CMOS microchips in a one‐transistor‐one‐resistor (1T1R) architecture. The MoS2‐based 1T1R cells exhibit forming‐free, nonvolatile resistive switching with ultra‐low operating voltages, low cycle‐to‐cycle variability ...
Jimin Lee   +16 more
wiley   +1 more source

Achieving High ON State Current through Ferroelectric Polarization‐Dependent Interfacial Resistance Switching in Undoped Orthorhombic HfO2 Films

open access: yesAdvanced Functional Materials, EarlyView.
Ferroelectric tunnel junction devices based on epitaxial undoped ferroelectric HfO2 films demonstrate stable switching endurance of over 106 switching cycles, low write voltages of ±3 V, 16 measured resistance states, and neuromorphic capability.
Markus Hellenbrand   +13 more
wiley   +1 more source

Analysis of 3D Printing Materials as Potential Radiological phantoms of Lung Organs for Medical Imaging purposes

open access: yesNigerian Journal of Technological Development
Research has been conducted to analyze and characterize ten 3D printing materials as potential Radiological Phantoms of Lung Organs. Eight filaments of PLA, ABS, HIPS, Carbon, Nylon, TPU, PETG, and Wood were printed using an FDM type 3D printer, and two
M. Yunianto, F. Anwar, T. D. Ardyanto
doaj  

Intermediate Filaments

open access: yesCold Spring Harbor Symposia on Quantitative Biology, 1982
M, Osborn   +4 more
openaire   +2 more sources

Home - About - Disclaimer - Privacy