Results 111 to 120 of about 231,416 (305)
Renmin Zhujiang, 2022 To study the engineering characteristics of fully weathered soft rock filling,we carried out indoor bearing ratio tests and compression tests on the fully weathered soft rock with compaction degrees of 96%,94% and 93% respectively.On this basis,we ...
GUO Zhiyu +4 more
doaj
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Design for Two-Fluid Fine Nozzle with 50% Fill Ratio [PDF]
Applied Mechanics and Materials, 2015 Sufficient air insert by reduced liquid in flashing propellants are required to produce fine droplet size with symmetrical spray in an aerosol atomiser without swirling design. It is called novel matched valve-actuator with two-fluid fine nozzle.
openaire +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
Tratamento de esgoto urbano em reator híbrido operado em baleladas sequenciais (RHBS) submetido a variações de cargas [PDF]
, 2008 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia Ambiental.Neste trabalho foi realizado o estudo do comportamento de um reator híbrido operado em bateladas seqüenciais (RHBS), no
Lamego Neto, Luiz Gonzaga
core
E3S Web of Conferences, 2018 The article presents laboratory tests of pressure compressibility characteristics of materials and backfilling. The tests were carried out for three different types of backfilling: rock fill (dry), hydraulic and paste in oedometers for three different ...
Skrzypkowski Krzysztof
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Case Studies in Thermal EngineeringClosed Loop-Pulsating Heat Pipes (CL-PHPs) are a promising heat transfer technologies known for their efficient and versatile thermal management capabilities. This study presents a comprehensive analysis of CL-PHPs employing Taguchi method.
Juluru Pavanu Sai +5 more
doaj +1 more source
Influence of femoral morphology and canal fill ratio on early radiological and clinical outcomes of uncemented total hip arthroplasty using a fully coated stem. [PDF]
Bone Joint Res, 2020 D'Ambrosio A +5 more
europepmc +1 more source