Results 151 to 160 of about 60,647 (283)

The Structural Refinement of Commercial‐Purity Copper Processed by Equal Channel Angular Pressing with Low Strain Amplitude

Advanced Engineering Materials, EarlyView.
Equal channel angular pressing of commercial pure copper under low strain amplitude (≈0.48) induces concurrent continuous and localized discontinuous dynamic recrystallization, forming a duplex structure influenced by strain heterogeneity and recovery. Moderate hardening after 4–12 passes results from progressive high‐angle grain boundary formation via
Paula Cibely Alves Flausino, Nayara A. N. da Silva, Bárbara C. de Almeida, Taise M. Manhabosco, Elaine C. S. Corrêa, Maria T. P. Aguilar, Paulo R. Cetlin   +6 more
wiley   +1 more source

Towards a New Early Warning System of Financial Crises [PDF]

, 2002
Matthieu Bussière, Marcel Fratzscher
openalex   +2 more sources

Domestic Bank Regulation and Financial Crises: Theory and Empirical Evidence from East Asia [PDF]

, 2001
Robert Dekle, Kenneth Kletzer
openalex   +1 more source

Toward Maximum Utilization of Heavy Rare Earths in Sintered Nd–Fe–B Magnets by Grain Boundary Diffusion Source and Application Area Optimization

Advanced Engineering Materials, EarlyView.
In this work, the grain boundary diffusion process is optimized to maximize heavy rare earth utilization by strategic magnetic hardening of areas in the magnet such as corners or edges that are highly susceptible to demagnetization, as demonstrated by finite element magnetostatics simulation on an internal permanent magnet, synchronous traction motor ...
Abdullatif Durgun, Dominik Ohmer, Matthias Katter, Andreas Thul, Simon Steentjes, Hossein Sepehri Amin, Oliver Gutfleisch, Imants Dirba   +7 more
wiley   +1 more source

Micromechanical Characterization of 316L‐V4E Steel Transitions Produced by Electron Beam Powder Bed Fusion with Dual‐Hopper Alternating Layer Strategy

Advanced Engineering Materials, EarlyView.
This work applies High‐Speed Nanoindentation to study multi‐material transitions in powder bed fusion–electron beam melting components. The aim is to assess the mechanical gradients and interfacial behavior between American iron and steel institute 316L stainless steel and V4E tool steel in additively manufactured structures.
Laia Ortiz‐Membrado, William Sjöström, Francesc Barberà Flichi, Carlos Botero, Anton S. Tremsin, Antonio Mateo, Emilio Jiménez‐Piqué   +6 more
wiley   +1 more source

Optimizing Laser Ablation of Stainless Steels for Volume Removal and Surface Quality Using Burst of Pulses

Advanced Engineering Materials, EarlyView.
This study explores the ablation efficiency and surface quality of laser‐treated stainless steel alloys (AISI 304, AISI 420, and AISI 316Ti) using an ultrashort pulsed laser and varying burst parameters (MHz, GHz, and Bi‐burst). Both ablation rates and surface quality parameters are determined, including isotropy surface roughness values, highlighting ...
Dirk Obergfell, Bahman Azarhoushang, Andrés Fabián Lasagni   +2 more
wiley   +1 more source

ANALISYS OF THE MEASURES FOR MONTENEGRIAN BANKING SYSTEM PROTECTION FROM THE CONSEQUENCES OF THE GLOBAL FINANCIAL CRISIS

Acta Economica, 2009
As globalization becomes more extensive, the spillover effect of the financial crises is intensifying more than ever before. Unfortunatelly, globalization means breaking not only barriers that lags international capital flows but also ones that block ...
Саша Поповић, PhD
doaj  

The Effects of Retention Measures on Retirement Timing-Do Financial Crises Matter? [PDF]

Front Sociol, 2019
Midtsundstad T, Hermansen Å.
europepmc   +1 more source

Deformation Behavior of Optical Ceramic Nanomultilayers: The Role of Aperiodicity

Advanced Engineering Materials, EarlyView.
Ceramic nanomultilayers demonstrate optical and mechanical behavior tunability through aperiodicity. Within the studied systems, optically optimized coatings exhibit an average ultraviolet, visible, and near‐infrared spectral transmittance above 90%.
Danielle E. White, Wenjuan Cheng, Koushik Jagadish, Edoardo Rossi, Yu‐Tsun Shao, Andrea M. Hodge   +5 more
wiley   +1 more source

Effect of Annealing Temperature on Microstructure and Dry‐Sliding Behavior of Powder Bed Fusion–Laser Beam Ti6Al2Sn4Zr6Mo Alloy

Advanced Engineering Materials, EarlyView.
Heat treatment parameters critically affect the wear resistance of powder bed fusion–laser beam (PBF‐LB)‐produced Ti–6Al–2Sn–4Zr–6Mo alloy. This study found that optimizing annealing temperature allows to obtain a tailored microstructure, which enhances the dry‐sliding behavior by forming a stable and functional mechanically mixed layer (MML), ensuring
Gianluca Pirro, Lavinia Tonelli, Carla Martini, Alessandra Martucci, Mariangela Lombardi, Lorella Ceschini   +5 more
wiley   +1 more source