Results 231 to 240 of about 16,939,992 (374)

Challenges during Flash Lamp Annealing of Aerosol‐Deposited Barium Titanate Films

Advanced Engineering Materials, EarlyView.
Aerosol deposition is used to rapidly deposit barium titanate films with thicknesses ranging from 2 to 16 μm at room temperature, eliminating the need for further densification. However, to recover the electromechanical properties, annealing is required, which limits the usage of temperature‐sensitive substrates.
Michel Kuhfuß, Juliette Cardoletti, Udo R. Eckstein, Shaoxiong Xie, Alexander Martin, Ken‐ichi Kakimoto, Sebastjan Glinšek, Kyle G. Webber   +7 more
wiley   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Financial Report [PDF]

Canadian Mathematical Bulletin, 1965
openaire   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

A Systematic Review on the Economic Burden of the Most Prevalent Infectious Diseases in West Africa. [PDF]

Health Sci Rep
Nyamekye KA, Sampane-Donkor E, Latif H, Aheto JMK.   +3 more
europepmc   +1 more source

Public accountability and government financial reporting

, 2012
Farzad Eivani
openalex   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

annual-report-and-financial-statements-2010

, 2016
St Patrick's University Hospital
openalex   +2 more sources

The impact of the professional accounting corporatisation upon the financial reporting quality [PDF]

, 2014
Slobodan Vidaković, Izet Banda, Danica Petrović   +2 more
openalex   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source