Results 191 to 200 of about 14,649,018 (327)

Inverse design framework for 4D printed structures using the finite element method. [PDF]

Sci Rep
Liu Z, Betha Cahaya Imani K, Wang M, Ma S, Furukawa H, Hirai S, Wang Z.   +6 more
europepmc   +1 more source

Amphoteric Cu‐Doping Leading to High Thermoelectric Performance in p‐Type Bismuth Antimony Telluride

Advanced Functional Materials, EarlyView.
This study shows that Cu plays two opposite roles in p‐type Bi0.5Sb1.5Te3 depending on the processing route. Under thermodynamic‐equilibrium bulk‐synthesis, Cu mainly occupies cation sites, increases hole concentration, preserves mobility, and slightly reduces lattice heat transport. The best‐performing composition among the investigated series reaches
Moritz Thiem, Zhiyuan Li, Minsu Heo, Fangyi Hu, Tian Lan, Youngdeog Koh, Ruiwen Xie, Chuanmu Tian, Marc Widenmeyer, Hyun‐Sik Kim, Jan P. Hofmann, Yuan Yu, Hongbin Zhang, Anke Weidenkaff, G. Jeffrey Snyder, Wenjie Xie   +15 more
wiley   +1 more source

Nonlinear dynamic analysis of pile foundation using finite element method. [PDF]

Sci Rep
Goshu T, Assefa E, Jilo NZ, Assefa SM, Pantelidis L, Sachpazis C, Mohammed H.   +6 more
europepmc   +1 more source

Sacrificial‐Layer‐Assisted Heat‐Affected‐Zone Suppression in Laser Patterning of PET for High‐Performance Flexible Devices

Advanced Functional Materials, EarlyView.
A removable sacrificial polymer layer engineers the thermal boundary condition during nanosecond laser ablation of PET, suppressing heat‐affected‐zone formation without relying on costly ultrafast lasers. This strategy enables deep, high‐aspect‐ratio trenches with no detectable heat‐affected zone, templating silver‐filled mesh electrodes with record ...
Mehdi Zarei, Mirza Sahaluddin, Mostafa Bedewy, Paul W. Leu   +3 more
wiley   +1 more source

Clarifying the origin of the interpubic cavity using a biomechanical model and the finite element method. [PDF]

Sci Rep
Horák Z, Mazura M, Báča V, Vilimek M, Salášek M, Blanková A, Kachlík D, Grill R, Džupa V.   +8 more
europepmc   +1 more source

Al3+/Ta5+ Co‐Doping Promotes Homogeneous Li+ Transport Enabling High Performance Ni‐Rich Layered Oxide Cathodes

Advanced Functional Materials, EarlyView.
Al3+/Ta5+ co‐doping refines the primary particles of LiNiO2, reduces Li/Ni antisite disorder, and expands the c‐axis lattice parameter, thereby enabling faster and more homogeneous Li+ transport. Such rapid and homogeneous Li+ transport suppresses high‐voltage phase transitions and microcrack formation, ultimately improving the rate capability and long‐
Yanhao Ren, Zezhou Lin, Zhaowen Bai, Wei Wang, Yangqian Zhang, Jihao Zhang, Qingyu Kong, Yisen Xu, Jiaqi Wu, Fengting Ye, Haitao Huang, Yang Ren   +11 more
wiley   +1 more source

On the Numerical Evaluation of Wall Shear Stress Using the Finite Element Method. [PDF]

Int J Numer Method Biomed Eng
Brunátová J, Dokken JS, Valen-Sendstad K, Hron J.   +3 more
europepmc   +1 more source

Nitride MXenes Beyond Carbides: Bridging the Gap Between Computational Prediction and Experimental Realization

Advanced Functional Materials, EarlyView.
Nitride MXenes remain constrained by a persistent gap between computational prediction and experimental realization. This Review identifies the thermodynamic, kinetic, and chemical barriers limiting their synthesis, critically evaluates emerging fabrication routes, and proposes a multidimensional computational‐experimental framework to accelerate the ...
Naresh Varnakavi, Masoud Soroush
wiley   +1 more source

An improved Wexler algorithm for electrical impedance tomography using finite element method and gradient based overrelaxation. [PDF]

Sci Rep
Jurgielewicz M, Walczyk CJ.
europepmc   +1 more source

Modeling, Design, and Development of Soft Pneumatic Actuators with Finite Element Method  

, 2016
P. Moseley, J. Florez, H. Sonar, Gunjan Agarwal, W. Curtin, J. Paik   +5 more
semanticscholar   +1 more source