Results 121 to 130 of about 1,318,615 (304)

Equivalent drawbead model in finite element simulations [PDF]

, 1996
In 3D simulations of the deep drawing process the drawbead geometries are seldom included. Therefore equivalent drawbeads are used. In order to investigate the drawbead behaviour a 2D plane strain finite element model was used.
Carleer, Bart D., Huetink, Han, Meinders, Timo   +2 more
core   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source

Ship hull model data processing algorithm for fast FEM modeling

Zhongguo Jianchuan Yanjiu
ObjectiveIn order to improve the efficiency of the finite element geometric modeling of hulls, to address the problem in which hull geometry models exported by ship design software cannot be directly used in finite element modeling，this study propose a ...
Rui LI, Mingfa WANG, Zhaochuang MENG, Guolei LIU, Yongtian QIU   +4 more
doaj   +1 more source

Finite element analysis of a composite material interface [PDF]

A finite element model of a composite material interface is developed to study the influence of the interface on the thermal strain in the composite. A plane stress model is used with an axisymmetric model as a check.
Murray, K. H.
core   +1 more source

Printed Integrated Logic Circuits Based on Chitosan‐Gated Organic Transistors for Future Edible Systems

Advanced Functional Materials, EarlyView.
Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco, Valerio Francesco Annese, Valerio Galli, Ilaria Penna, Debora Russo, Marina Veronesi, Rita Scarpelli, Stefania Sabella, Mario Caironi   +8 more
wiley   +1 more source

Intrinsic finite element modeling of a linear membrane shell problem

, 2012
A Galerkin finite element method for the membrane elasticity problem on a meshed surface is constructed by using two-dimensional elements extended into three dimensions.
Hansbo, Peter, Larson, Mats G.
core  

Positive‐Tone Nanolithography of Antimony Trisulfide with Femtosecond Laser Wet‐Etching

Advanced Functional Materials, EarlyView.
A butyldithiocarbamic acid (BDCA) etchant is used to fabricate various micro‐ and nanoscale structures on amorphous antimony trisulfide (a‐Sb2S3) thin film via femtosecond laser etching. Numerical analysis and experimental results elucidate the patterning mechanism on gold (reflective) and quartz (transmissive) substrates.
Abhrodeep Dey, Uwe Hübner, Albane Benardais, Xiaofei Wu, Andrea Dellith, Jan Dellith, Torsten Wieduwilt, Henrik Schneidewind, Markus A Schmidt, Virginie Nazabal, Volker Deckert, Jer‐Shing Huang, Wei Wang   +12 more
wiley   +1 more source

MOFs and COFs in Electronics: Bridging the Gap between Intrinsic Properties and Measured Performance

Advanced Functional Materials, EarlyView.
Metal‐organic frameworks (MOFs) and covalent organic frameworks (COFs) hold promise for advanced electronics. However, discrepancies in reported electrical conductivities highlight the importance of measurement methodologies. This review explores intrinsic charge transport mechanisms and extrinsic factors influencing performance, and critically ...
Jonas F. Pöhls, R. Thomas Weitz
wiley   +1 more source

In Situ Study of Resistive Switching in a Nitride‐Based Memristive Device

Advanced Functional Materials, EarlyView.
In situ TEM biasing experiment demonstrates the volatile I‐V characteristic of MIM lamella device. In situ STEM‐EELS Ti L2/L3 ratio maps provide direct evidence of the oxygen vacancies migrations under positive/negative electrical bias, which is critical for revealing the RS mechanism for the MIM lamella device.
Di Zhang, Rohan Dhall, Matthew M. Schneider, Cun Li, Chengyu Song, Sundar Kunwar, Hongyi Dou, Natanii R. Yazzie, Henry Tran, Daniel Appuing, Jim Ciston, Nicholas G. Cucciniello, Pinku Roy, Michael T. Pettes, John Watt, Winson Kuo, Haiyan Wang, Ye Cao, Rodney J. McCabe, Aiping Chen   +19 more
wiley   +1 more source

Three‐dimensional Antimony Sulfide Based Flat Optics

Advanced Functional Materials, EarlyView.
This work presents the development of a grayscale electron beam lithography (g‐EBL) method for fabricating antimony trisulfide (Sb2S3) nanostructures with customizable 3D profiles. The refractive index of g‐EBL patterned Sb2S3 is determined based on the synergy of genetic algorithm and transfer matrix method.
Wei Wang, Uwe Hübner, Anne Gärtner, Tao Chen, Joseph Köbel, Franka Jahn, Daniel Repp, Abhrodeep Dey, Henrik Schneidwind, Andrea Dellith, Jan Dellith, Torsten Wieduwilt, Matthias Zeisberger, Tanveer Ahmed Shaik, Astrid Bingel, Markus A. Schmidt, Jer‐Shing Huang, Ulf Peschel, Volker Deckert   +18 more
wiley   +1 more source